Question about Samsung HT-DS400 System

Open Question

My samsung CINEMA HT-DS400 doesn't start up (hello,protection)

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Problem with DVD player

i have had samsung surround sound for couple months, only been used once, now when i power up, protect is displayed on front and then powers down, also, when it does work, sound is extremely low compared to when i first used it.

Posted on Oct 21, 2008

Ad
  • 1 Answer

SOURCE: Samsung home cinema system HT-THX25 Multiregion hacks

Turn on the HT with no DVD. Press the following buttons on the remote: ENTER 8, 4, 2, 6, 9 ENTER 
It will turn off. When turned again on it is a region free HT. 

Posted on Nov 26, 2008

ginko
  • 19396 Answers

SOURCE: SAMSUNG HT-TZ212 home cinema kit comes up with protect

Protect mode will kicking whenever a fault is detected.

Causes that can start protect mode are:

Electrostatic harges on internal circuits.
Leave the unit unplugged for power for one hour or so, this will allow discharge.

Bad speaker wiring.
Check speaker wiring, try unplugging and plugging back, or start after removing one speaker at the time.

Internal fault.
Internal fault is the natural cause for protect mode. If all the above did not work, then the problem is a blown component or an internal fault. In this case the unit must be taken apart , tested and repaired by an experienced person.
If the unit is less than one year old, or if you want to get service, call Sony at the phone number listed on the product documentation.

Regards.

Posted on May 04, 2009

chipsandnuts
  • 70 Answers

SOURCE: Hello Protection Samsung HT-DS900

When your home theater's display reads PROTECTION, it means the home theater is over heating and the unit will shut down to prevent any damage. This can happen if the unit is stacked along with other electronic devices or the unit is in an enclosed area that prevents the unit from cooling properly. To decrease the chance of overheating, relocate your home theater to a more open area.



If the home theater display reads PROTECTION every time you turn it on, no matter where or how the unit is placed, it needs service. To set up service call Samsung Customer Care at 1-800-SAMSUNG (1-800-726-7864). Have your model number and serial number on hand to set up service.

Posted on Jul 03, 2009

bogue-engine
  • 24 Answers

SOURCE: ht-z210 home cinema protect error

Protection Error means that there is a malfunctioning component inside your unit. It will go into protection mode and immediately shut down to protect your system from any further damage. Unfortunately you would have to bring it to a dealer or repair shop to diagnose the exact malfunction and that could be expensive.
Gary

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Samsung dvd player switches itself onto protect!


hi,i can't connect my audio tv to cinema theater dvd

Apr 02, 2010 | Televison & Video

1 Answer

Samsung hiome cinema protect error message


you need to change 5q tranzistor.if you dont have short circuit on pin 9 to ground on flat who comes from amplifier

Aug 04, 2009 | Samsung HT-X20 Home Cinema 600W Theater...

1 Answer

Ht-z210 home cinema protect error


Protection Error means that there is a malfunctioning component inside your unit. It will go into protection mode and immediately shut down to protect your system from any further damage. Unfortunately you would have to bring it to a dealer or repair shop to diagnose the exact malfunction and that could be expensive.
Gary

Jul 18, 2009 | Samsung HT-X20 Home Cinema 600W Theater...

1 Answer

Protection displayed and shuts off When I press the power button Protection is appear on screen on my home cinema system dvd player


check wiring on speakers it sounds like you have some wires touching together somewhere or you have a bad speaker.

Jun 15, 2009 | Samsung HT-X20 Home Cinema 600W Theater...

1 Answer

Hello Protection Samsung HT-DS900


When your home theater's display reads PROTECTION, it means the home theater is over heating and the unit will shut down to prevent any damage. This can happen if the unit is stacked along with other electronic devices or the unit is in an enclosed area that prevents the unit from cooling properly. To decrease the chance of overheating, relocate your home theater to a more open area.



If the home theater display reads PROTECTION every time you turn it on, no matter where or how the unit is placed, it needs service. To set up service call Samsung Customer Care at 1-800-SAMSUNG (1-800-726-7864). Have your model number and serial number on hand to set up service.

Jun 14, 2009 | Samsung HT-DS400 System

1 Answer

Samsung HT-A100 Home Cinema system plays cd only with tv on!


Hi,
You need to put away the remote for your TV and use only the remote for your HT system. Your HT remote should work on your TV by default. Your Samsung HT remote should have a TV button and a DVD/Receiver button (or HT button). When using only the TV, press the TV button and then use it for just the TV and when using the HT system, press the DVD/Receiver button and then you can use the HT system.
If for some reason your TV is not set on the Samsung HT remote by default, your HT users manual should have a list of codes that you can use to program your HT remote. Hope that helps you. Gary

Mar 18, 2009 | Samsung HT-A100T Theater System

2 Answers

SAMSUNG HT-TZ212 home cinema kit comes up with protect


Protect mode will kicking whenever a fault is detected.

Causes that can start protect mode are:

Electrostatic harges on internal circuits.
Leave the unit unplugged for power for one hour or so, this will allow discharge.

Bad speaker wiring.
Check speaker wiring, try unplugging and plugging back, or start after removing one speaker at the time.

Internal fault.
Internal fault is the natural cause for protect mode. If all the above did not work, then the problem is a blown component or an internal fault. In this case the unit must be taken apart , tested and repaired by an experienced person.
If the unit is less than one year old, or if you want to get service, call Sony at the phone number listed on the product documentation.

Regards.

Nov 14, 2008 | Samsung 500w Rrss Rear Reflecting Surround...

Not finding what you are looking for?
Samsung HT-DS400 System Logo

Related Topics:

420 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Audio Players & Recorders Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Electric Dime
Electric Dime

Level 3 Expert

434 Answers

The Knight
The Knight

Level 3 Expert

74198 Answers

Are you a Samsung Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...