Question about Hotpoint Aquarius WF000 Front Load Washer
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: My Hotpoint Aquarius plus 1400
Your inlet valve at behind top of machine is defective; or the pressure from your faucet is insufficient.
Close your faucet valve on wall & unscrew your hoses to check screens on hoses & machine. Clean out well. See that the water pressure is good. Refit, check for leaks. If this is not the problem change your inlet valve, it is easily done.
Sites for spares:
RepairClinic.com (which is good)
Pl rate if helped.............
Posted on Jun 13, 2008
Hiya Barry, I have the same machine and for the last 3 days have had the exact same problem...mini load and reduced crease as well as power light flash right when it comes to drain...?
I have scratched my head and done lots and lots of research, reckon I could design and build my own washer now lol, anyway, I fitted a new pump and ran it, thinking this is it sorted, went out and got a call from our lass...doing it again.
Right, gonna have to get me hands dirty...I removed the drain hose (Ignore the pump for a second, I'm talking about the grey hose that goes from the pump to the sink) from the sink and poked my fingers as far as they would go...debris, I then removed it from the other end (Pump) so I had a long hose in my hands, not attached to anything at either end....cleared it and again, loads of debris (Fluff, plastic etc) and put it all back together...turned the old fella back on and running a wash right now as we speak...happily spinning round at 1400rpm and throwing gallons of water down the sink...I would consider it fixed.
So I can most definately tell you that you have a blockage somewhere mate, I'd get your hands in the toolbox and pull that pipe off, doesn't require any level of experience, just the ability to put things back as you found them...
Hope that helps
Posted on Dec 01, 2008
Tips for a great answer:
Nov 22, 2016 | Hotpoint Washing Machines
Oct 27, 2015 | Hotpoint Aquarius WD640 Front Load...
Please read in full before attempting
p.s. Before working on machine "turn of the
Only carry out if you are confident that you can carry out safely.
Note check small black hose to the air pressure switch is connected,
When machine is turned upside down, the
hose has a tendency to come off.
If unsure call a service engineer.
My machine just had the flashing "door" fault.
On carrying out fault finding checks,
I Found that the main PCB had a built up dust.
This dust was in black lines going between components of the board.
Cleaned around components of the board with a small soft brush.
assembled & tested okay 2 months ago & still working.
Mar 31, 2013 | Hotpoint Aquarius WD640 Front Load...
Dec 04, 2010 | Hotpoint Washing Machines
Dec 18, 2009 | Hotpoint Ariston Aquarius WD420 Front Load...
Oct 20, 2009 | Hotpoint Aquarius WD640 Front Load...
Feb 20, 2009 | Hotpoint Aquarius WMA42 Front Load Washer
Jan 05, 2009 | Hotpoint Aquarius WD640 Front Load...
Jun 13, 2017 | Hotpoint Washing Machines
Nov 03, 2007 | Hotpoint Aquarius WMA56 Front Load Washer
587 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: