Question about DVD & Blu-Ray Players

1 Answer

The loader for cd's stays in the loaded position.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Hi again,

Anything new after the reset?

Posted on May 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

No recording, open close error.


Details:
  1. Open - close error, can not load dvd and the led is blinking.
  2. After replace Main PCB, Loader and HD, conditions still same as before.
Follow this method:

Format the Hard drive, with steps as below :
a. DVD condition on --> Loading.
b. Press cancel button on remote until ST-BY appear on display set.
c. Press cursor up or down on remote until CD-UP appear on display Set.
d. Wait until formatting is complete.
Test open - close DVD.
a. If process open - close is normal, change the Assy Loader.
b. If Process open - close is fail , change the HD.

Damage loader can cause open-close error and error on HD.

on Mar 29, 2011 | Samsung DVD-HR735 DVD Recorder/HDD...

1 Answer

My sony progressive scan 5 dvd/cd changer door won't shut, first it wouldn't open, thej i used a small screw driver, and pried it open, then it open then won't shut?


This is a loader mechanisn fault. Mithe be eiter to a loose loding belt, or defective loading gear wheels.

Visit this site for more details. Type in the site name "Electro-help" either to Google or Yahoo search box [not in the address bar of your browser], and click search. It is an electronic equipments service help site. All details you want are there. Note the position of hyphen in between words in site name, when you type it in. The site will appear as it is in web; subtitled as electronics equipments' repair help.

May 17, 2012 | Sony DVD & Blu-Ray Players

1 Answer

LG DRT389H will switch on OK but the disc draw will close when a disc is loaded, but comes straight out again and will not play.


Hello
There is a loading motor and a belt associated with it, connected to a gear wheel assembly that pulls in the disc tray as well as gets it out. If the loading belt, said above, will get loose, the disc loading tray wont get into it properly. There is a sensor switch fitted inside the loading mechanism, which senses the proper tray in action, as this tray will touch it when it ahs been fullly loaded. Due to any reason, the switch said above does not engaged properly, the main system control IC will detect the loader position to be improper, and will give command to eject the tray. That is now happening to your DVD player.
If you have knledge and experience, just open your DVD player. locate the loading belt, and repalce it with a new one. You can buy this belt from most of the electronic sparepart selling shops at your town. Just keep the old belt in hand as a sample, when you go to buy a new one. OK

WISH YOU A HAPPY PROSPEROUS 2012
Gopakumar G, Trivandrum City, Kerala State, South India.

Dec 27, 2011 | DVD & Blu-Ray Players

1 Answer

Can you manually release a DVD from the Panasonic S32? The DVD player 'died' - with a CD inside. The instructions are silent on a manual solution.


Hi there,

Well you can please follow the below steps -
1. Unplug the DVD player and take the outer casing of the DVD player off. This entails either taking out two or three screws or simply sliding one of the pieces of plastic in either direction.
2. Locate the disc loader cover. The disc loader cover is located where the extending DVD tray finally comes to rest within the DVD player. It's the part that holds the DVD loader in place.
3. Bend the two tabs outward that hold the loader in place. This is a delicate procedure because you don't want to hurt the device. The tabs are relatively easy to break since they're plastic in most cases.
4. Slide the disc tray out. If your disc got stuck before it was read, it's probably still on this tray. If so, your problem is solved. However, if the disc was fully set and loaded, the job isn't quite finished yet.
5. Move the small mechanical arm that holds the disc in place over so that the disc and the reader are both exposed. Some DVD players will not have anything holding the disc in place. Instead, these devices use a system not unlike that of a common DVD case. The DVD will be locked in place in the center.
6. Carefully lift the disc up and out of its loaded position in the DVD player. This may entail sliding the disc reading mechanism over slightly. This won't hurt the device as long as you're careful. You should be able to access and remove the disc.

Good Luck!!

Apr 01, 2010 | Panasonic DVD & Blu-Ray Players

1 Answer

CD/DVD drawer won't open so CD stuck inside :(


Hi there,

Well you can please follow the below steps -
1. Unplug the DVD player and take the outer casing of the DVD player off. This entails either taking out two or three screws or simply sliding one of the pieces of plastic in either direction.
2. Locate the disc loader cover. The disc loader cover is located where the extending DVD tray finally comes to rest within the DVD player. It's the part that holds the DVD loader in place.
3. Bend the two tabs outward that hold the loader in place. This is a delicate procedure because you don't want to hurt the device. The tabs are relatively easy to break since they're plastic in most cases.
4. Slide the disc tray out. If your disc got stuck before it was read, it's probably still on this tray. If so, your problem is solved. However, if the disc was fully set and loaded, the job isn't quite finished yet.
5. Move the small mechanical arm that holds the disc in place over so that the disc and the reader are both exposed. Some DVD players will not have anything holding the disc in place. Instead, these devices use a system not unlike that of a common DVD case. The DVD will be locked in place in the center.
6. Carefully lift the disc up and out of its loaded position in the DVD player. This may entail sliding the disc reading mechanism over slightly. This won't hurt the device as long as you're careful. You should be able to access and remove the disc.

Good Luck!! Thanks for using FixYa!!

Feb 03, 2010 | Cambridge Audio Azur 540D DVD Player

1 Answer

My Yamaha S-30 dvd player will no longer play any discs


it sounds like the unit needs its dvd loader or laser ***'y replaced. try cleaning the laser with a soft cotton bud first, if that doesnt work, replace thae loader assy.

Jul 04, 2009 | DVD & Blu-Ray Players

1 Answer

I am unable to eject a DVD disk from the player either with the remote or player mounted buttons. Your advice would be appreciated.


do this with the unit off:1Unplug the DVD player and take the outer casing of the DVD player off. This entails either taking out two or three screws or simply sliding one of the pieces of plastic in either direction.
Step2Locate the disc loader cover. The disc loader cover is located where the extending DVD tray finally comes to rest within the DVD player. It’s the part that holds the DVD loader in place. Step3Bend the two tabs outward that hold the loader in place. This is a delicate procedure because you don’t want to hurt the device. The tabs are relatively easy to break since they're plastic in most cases. Step4Slide the disc tray out. If your disc got stuck before it was read, it's probably still on this tray. If so, your problem is solved. However, if the disc was fully set and loaded, the job isn’t quite finished yet. Step5Move the small mechanical arm that holds the disc in place over so that the disc and the reader are both exposed. Some DVD players will not have anything holding the disc in place. Instead, these devices use a system not unlike that of a common DVD case. The DVD will be locked in place in the center. Step6Carefully lift the disc up and out of its loaded position in the DVD player. This may entail sliding the disc reading mechanism over slightly. This won't hurt the device as long as you’re careful. You should be able to access and remove the disc.
if this helps dont forget to leave a fixya rating as thats how we get paid

Apr 25, 2009 | Toshiba SD-K220S DVD/CD Player w/Built-in...

1 Answer

Screen comes on, disk turns, loading starts, and doesnt stop


With the power turned off, open the DVD Player, and then open the top where you load the DVD into the player. Locate the laser lens and notice that the laser is attached to a transport assembly that moves the laser diagonally outward in a slot. 1. Slide this assembly outward to the end of its track. 2. Slide the assembly back inward to the closest inward position. 3. Repeat the process of sliding the assembly outward and then back inward.4. Put in a music CD and let it play all the way through. This helps to calibrate the laser head assembly movement. When the music CD is finished playing. 5. Put in a DVD, and you should have a working unit again This is a factory solution from Mintek that was given to a customer who ask for help with the forever loading disc problems. This solution may work on other models of portable DVD players. Most portable DVD players use this type of transport mechanism. Try this solution it might work for you.

Feb 01, 2009 | Mintek MDP-1770 Portable DVD Player

1 Answer

Problem loading disc


just open the loader and replace the lense.

Jul 23, 2008 | Dynex DX-PDVD7 Portable DVD Player

Not finding what you are looking for?
DVD & Blu-Ray Players Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top DVD & Blu-Ray Players Experts

kakima

Level 3 Expert

96576 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...