How do i use the Stanley caulk gun? - Grip On Tools Grip Heavy Duty Caulking Gun

get caulk and a caulk gun at the local hardware or Walmart. Load the caulk tube into the tray part of the caulk gun, snip the end of the tube. push on the rear of the tube and slowly lay a bead of caulk around the area of the tub needing caulk.

No you don't. We answer most things here.

If the stapler is like any of these

http://www.amazon.com/s?ie=UTF8&page=1&rh=i%3Aaps%2Ck%3Abostitch%20staple%20gun

You push the back in slightly to unlatch it and then drop it down a bit and the staple pusher comes out completely.

Stanley Model TR45 Light Duty Staple Gun Review - YouTube

? 3:35
https://www.youtube.com/watch?v=hWmvXhkqnYI
Jul 25, 2012 - Uploaded by Vansvideoreviews
Stanley Model TR45 Light Duty Staple Gun Review ... How toPut Staples in a Craftsman Stapler (Model 968447) ... Stanley SharpShooter Manual Staple and Brad Gun review - Duration: 9:35. by Unpack Guy 35,948 views.

How to load staples into a Stanley Stapler - YouTube

? 2:11
https://www.youtube.com/watch?v=j4Q5W0uKS-s
Mar 26, 2013 - Uploaded by David DeStefano
This video shows you how to load staples into a Stanley StaplerModel # TR110. ... Stanley SharpShooter Manual Staple and Brad Gun review ...

put stanley sharpshooter staple gun back together ... - Fixya

www.fixya.com > Forum > Tags

Find solutions to your put stanley sharpshooter staple gun back together question. ... staples for the TRE500 Stanley Sharpshooter Electric Heavy Duty Stapler.

I would suggest using 'relief cuts' in the strip so you can make the bend, and then continue -- though using a caulk gun would be better. With standard caulk you can just use your finger and a little water to leave a nice finish. I believe you will find it cheaper as well -- a tube of caulk is around 2 or 3 dollars -- and a caulk gun is a dollar or so.

http://youtu.be/qARPdyLwkb0

There should be a thumb release on the shaft at the handle end, press with your thumb and then pull back with the other hand on the shaft. If you have a used tube in the gun, it could be that some of the caulk came out the inside of the tube and hardened so that you cannot pull back the shaft, you will now have to cut the tube off with a utility knife to remove the old dried caulk

How to Fix Loose Tile Floor with Fix Floor How to Repair Hollow Tile Floor...
Use a caulking gun that can use 10 oz. caulking tubes. http://www.premierbuildingsolutions.net/wp-content/uploads/jpg/130604-PIS-HPCaulkingGun-SausageGun.jpg

For professional work I use the Ryobi 18 volt gun which is a bit more expensive than your basic gun like a Workforce 60:20 gun.

Cut the end of tube on a angle.There should be a rod with what looks like a plunger at the end.pull the rod back as far as it will go and lock into place.slide tube of caulk into gun with open end of tube towards the plunger.should be a slot at other end where nozzle fits in.take a piece of wire and poke a hole up the nozzle of the tube.release the rod and sqeeze the handle a few times you should see the rod start moving.if not turn the rod until the teeth are facing down.then try again .you should hear a clicking sound and feel pressure and caulk will begin to come out of tube and you will be caulking.Good luck.If you still have problems just come back to fix-ya and we,ll help you through it.

there should be a button / lever at the rear press it and it should open so as to insert the staples

you can leave them down without releasing the pressure and discover when you return that you have a great big mess to clean up...i hope this helps