Question about Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

I can't push any buttons

The only button that will actually push in is the Power button. Is there something I'm missing?

Posted by on

1 Answer

Sad to say, your board is defective.

Posted on Jun 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dishwashers will not switch on. The power is connected, but when pushing the button, nothing happens.


Maybe you did not connect it properly in the first place. Try to ask a Tecnician to check the power Supply board cos next time you might not be able to start it

Jan 27, 2014 | Electrolux Dishwashers

2 Answers

How do you reset a KitchenAid dishwasher model: KUDE70FXSS4?


Press High Temp Scrub and Dry Heat option buttons in quick succession one after the other for about 6 sec until all the lights come on. Then press Cancel button. This should reset the dishwasher. Press equivalent buttons on the panel if the actual ones above are not there.
Make sure the dishwasher detergent dispenser lid is shut and the dishwasher door is shut before you start the above reset sequence.

Jan 02, 2013 | KitchenAid Dishwashers

2 Answers

I can't turn on my KitchenAid Superba dishwasher. I pushed Normal and Start, and the Normal light started flashing, but didn't turn on. Pushed Cancel and now both the Normal and Cancel are...


Did you try turning off the power and then connecting it again?
If still problem is there open the door. Press the following sequence of buttons HI Temp Scrub, Energy Saver Dry,HI Temp Scrub, Energy Saver Dry. Now close the dishwasher door and latch it too and press the cancel button. This must reset the dishwasher.

Aug 13, 2011 | KitchenAid 24 in. KUDU02FR Built-in...

1 Answer

Fisher Paykel DS605i single dishdrawer with a user-supplied integrate panel. There are three buttons on front. The left-hand button is power button; the center button is start/pause; and the right-hand...


Hello, Thank You for using FixYa. I will be helping you today.Are any of the cycle lights lighting up like rinse and normal and is the light on front blinking and pausing if so how many times is it blinking? Try turning the power off too the unit for five minutes and back on, because if the lid was open some or was stuck it can stop the unit from running.
Thank You and please ACCEPT my answer and Rate my answer if it was helpful..

Jun 29, 2011 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

The dishwasher won't start, its stuck, pots/pan button is blinking, & the timer has (2)_ _ bars blinking. I tried to reset/pushed the start/resume button nothing happened. I pushed the cancel/drain...


did you hold the start/resume button for at least 3 seconds if this works the dishwasher will start ok but if there is a fault it will fail again best you contact your nearest service agent good luck

Apr 07, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Flashing lights on Maytag dishwasher


Check whether the door is getting closed fully. Try pushing little hard. If the door close switch problem it may work.

Contact service for help if u can not proceed further with electrical circuits. Micro-controller board to be checked!

May 18, 2010 | Dishwashers

1 Answer

I have a kenmore Elite Ultra Wash Dishwasher that won't run. The lights for the various wash and dry options come on, but when I push the start button, it flashes green three times and then goes off.


Sounds like a safety - lock is operating.

Close and press start button - keep button derpressed untill machine actually starts - maybe 8 seconds or so.

If this does not do it, unplug for 24 hours then try again.

Aug 04, 2009 | Dishwashers

1 Answer

My dishwasher won't actually turn on this morning. When I push the start button, it hums, and the lights by the cycles flash, for about two minutes, but it won't actually run through a cycle.


Your motor is probably stuck.
Remove power from the D/W.
Remove the lower access panel. The motor will be in front of you.
Turn the blades in the end of the motor counterclockwise until the motor turns freely. You will need a flat screwdriver to reach in and turn the blades.
When it frees, repower and try it again.

Mar 14, 2009 | GE Adora GHDA654LBG Dishwasher

1 Answer

Dishwasher quit during cycle.


Need a little more info.. anyway.. open dr will shut off dw...close dr.. push power button until power on... lights on, but nothing happen.. try holding down drain and one of wash cycle.. repeat holding drain w/other buttons until you hear drain pump running.. make sure you hold both buttons for a few seconds.. if your drain pump works.. then, you might have a problem w/your wash motor or something is stuck in the impeller area.

Jan 13, 2009 | Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Dishwasher problem Model number GSD2200LO1


No, he didn't do anything wrong. Swithching to energy saver setting only prevents power from going to the heating element during the drying portion of the cycle. I suspect that you have no power going to the dishwasher. Check the household breaker for the dishwasher. If that is not tripped (probably not) then your dishwasher power may be supplied through a GFI (ground fault interupter) protected outlet which has tripped. Look around the kitchen for GFI recepticles, as there may be several. Power may even be fed from a GFI from another room, such as a bathroom. Push the reset on all GFI recepticles you can find. You can purchase a small pen sized tester for under $20 which will show if a wire is carrying power without even thouching an actual wire. Pick one up at a hardware store to help see if power is reaching your dishwasher if you need more help.

Sep 25, 2008 | GE Dishwashers

Not finding what you are looking for?
Bosch 24 in. SHU43 Built-in Dishwasher Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

prem mathew

Level 3 Expert

662 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...