Question about Office Equipment & Supplies

1 Answer

Acco /Springline Optima Model #848 Stapler Repair

Have a small tension spring about 3/4" long, don't know where it goes????
Need schematic diagram or exploded view to repair.

Posted by on

  • hummingbrd84 Jan 27, 2009

    I also am wondering where the spring of the same size goes. Teh Interwebby isn't giving me any helpful diagrams. I believe it goes somewhere underneath the staple magazine, but I'm not exactly sure where?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,037 Answers

This is a stapler or a shredder?

If it is a stapler then it should connect to the metal sliding piece that pushes the staples forward and then it should also hook to the front/top of the stapler and possibly through a hole in the front and to the back. I'm not too familiar with this exact stapler. I don't have a diagram for it but if you go to a store that sells them, you could possibly find out there if you still can't get it. I hope this was helpful.

Let me know, thanks.

Posted on May 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to put the spring back in the handle of Arrow T50 Stapler?


Ref. recocking the spring handle in your Arrow T 50 Stapler
1. secure the stapler in a vise. You need three hands to recock the handle spring.
2. Using a notched tack lifter hand tool, with one hand holding the handle so as to expose the spring, place the notched tool against the spring arm and force it to the rear. it will now be under tension.
3. Wiggle the handle into position so that you can quickly insert the clevis pin. Once secured, let go your handle that is now under tension. Replace clevis ring.
4. Dry fire to test.

Sep 18, 2014 | Arrow Staple T50 3/8"" Monel stainless...

1 Answer

I have a 2007 optima... that need a new serpentine belt


Draw a diagram of where the belt is routed prior to removal. This will ensure you get it back on right. It should have a spring loaded tensioner. If you look at all the pullys one will have a 3/8 square hole or a big nut type thing. you need to get your 3/8 drive or socket & lever it back from the belt & remove off 1 pully (normaly p/steer is the easiest to get to. slowly release tensioner, finish removeing, then reverse the procedure to go back on

Jun 21, 2012 | 2004 Kia Optima

1 Answer

Schematic diagram to repair a STIHL FS 45 trimmer


hello, need a operators,parts manual for a stihl,echo chainsaw,hedge trimmer,line trimmer,edger,pole saws,concrete saw, as far as i know thay don't post any of these on line for the consumer,if i had a dealer number than i would be able to provide you with one,these manuals are available through the dealer only,hope this helps.``

Jan 11, 2012 | Garden

2 Answers

I unscrewed the part over the light bulb, than the smaller part that holds the thread tension bit and a small coil fell off, I don't know where it goes back, can I find anywhere a diagram of the machi


I cannot help and doubt a diagram could be found with that much detail but you could try the manufacturer. I suspect that the coil had been around the screw you removed or in the screw hole.

Dec 01, 2011 | Janome Harmony 2039 Mechanical Sewing...

1 Answer

Cratftsman Lawnmower; 16.5 horse; 42 inch deck, need assistance replacing armbrake and tension spring #58 on sears schematic; MOwer model number is 917271120-- particularly, where does this spring attach?...


Judging by the diagram the spring mounts under the armbrake, the Bolt (#52) goes through the circular spring. One end of the spring goes into one of the holes near the bolt on the armbrake and the other ( after providing tension by turning the spring ) must attach to a non moving part on the deck to be able to provide the required tension Look for a small turned up piece of metal with a notch in it on the housing.
Hope this helps

May 18, 2011 | Garden

1 Answer

Trying to load the staples into a model #90010. They're fine except at the very front of the stapler, they wont go all the way down flush with the others and the chamber won't even close.


1. Make sure you have the correct staples for the machine, Swingline Hvy-Duty Staples for 90010 Stapler, 0.625-Inch Leg Length, 2500 per Box (90009)


2. Check the staples to make sure there are no visible jams. Remove some staples from the row if this helps them fit.

3. If you continue to have problems, contact the manufacturer at http://www.acco.com/swingline/, or
Repair Service/Technical Support:
Phone: 800.790.7787

They will replace the stapler if needed.

Apr 14, 2011 | Swingline ® LightTouch Heavy-Duty Stapler,...

2 Answers

Swingline 270 (69270) Staple ends are left mostly open Also, stapler makes a significant popping noise with each use


Swingline, now owned by ACCO, should have a service manual that would tell you how to clear jams - here's the url - http://www.acco.com/contactus.aspx#swingline. If not, you can also send them your question directly so they can help you resolve the issue.

Jan 27, 2011 | Office Equipment & Supplies

1 Answer

My craftsman easy fire stapler diagram


Mine stopped working last night. I took it apart and was able to reassemble it properly.

When both sides are rejoined the tip of the spring has to be inserted in the hole on the corresponding side (note red arrows on both pics)

This is a great stapler when it's working.

c795842.jpg60304ed.jpg

Nov 22, 2009 | Tools & Hardware - Others

1 Answer

Safety B


Sounds as if you have a small Bostitch nailer/stapler. Bostitch lables its safety mech parts as Safety A for the part that actually contacts the work and Safety B for the part that contacts the trigger. Go to www.Bostitch.com and look for diagram of your gun. These two parts fit snuggly just behind the outer-most guide/nose. Safety b sits on top of safety a. There is usually a thumb adjustment and a spring between the two parts. The spring is usually installed on top of safety a and below the adjustment knob. enjoy

Nov 23, 2008 | Air Tools & Compressors

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

592 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

70365 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...