Question about Black & Decker Compact Power Screwdriver

1 Answer

Black & Decker Drill (Motor does not work on Forward switch but it is ok on reverse)

Black & Decker drill does not work on Forward Switch but it is ok on Reverse)

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Scraped the drill and bought a new one for $20

Posted on May 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I reverse the direction on the drill?


Above the trigger there is a black slide switch that will reverse the direction if its in the colckwise direction the richt side is pushed in if counter clockwise the left side is pushed in.

Apr 06, 2016 | Black & Decker Black and Decker FIRESTORM...

3 Answers

Where is the reverse switch on my black & decker 1/4 7004 drill type 1


The now vintage B&D model 7004 type 1 was a single-speed, non-reversible drill. There is no reverse switch.

Mar 21, 2015 | Black & Decker Drills

1 Answer

Have b&d firestorm 14.5 volt cordless, forward and reverse switch broken older model but hate to throw it away. it is stuck in forward andhave two batteries and good charger throw away? or fix ?


Fix! We had the same problem, and when we opened up the case (8 screws and a pin later), we found that a tiny plastic tab had broken off the Forward/Reverse selector, which costs less than a dollar. We ordered it from a local supplier to avoid $10 shipping.

Aug 30, 2011 | Black & Decker & Cordless Drill

1 Answer

How do i remove the bit from the drill


This drill has a 2-level chuck handle. one is slightly larger diameter, or is closer to drill body. It is fixed to the motor shaft. Smaller diameter, or forward one is the adjustment. Hold the rear/larger one stationary and twist the smaller/forward one as if you were opening a water bottle with a really tight lid.

Sep 17, 2010 | Black & Decker 3/8" Variable Speed...

2 Answers

No reverse on drill.


I am assuming the new switch was wired correctly, I would look for the pin or similar device that switches it from for/rev. If your switch has a post look at the slider and make sure not broke or your pin not put in rightt position. Let me know

Apr 22, 2010 | Black & Decker Drills

2 Answers

How do I attach the drill bit to the chuck on a ss 120 drill


Well I couldn't find a pix of your drill so I will guess that it is a typical drill. You seem to be asking a very basic question so I will start will all the basic info I can think of.

First you have to know where the power trigger is to make it go.

2nd you have to know where the forward and reverse switch is.

Now with the switch in the forward position squeeze the trigger to make it go. Then gently grab the chuck with your hand while it is going and the center Jaws should close up and come out of the chuck.

Now with the switch in the reverse position squeeze the trigger to make it go. Then gently grab the chuck with your hand while it is going and the cetner Jaws should open up and go into the chuck to a maximum point

Open the jaws enough to put the drill in the jaws then put the switch in the forward position. Put the drill in the chuck, sqeeze the trigger to make it go, and hold the chuck so the jaws close on the drill. All while keeping the drill from falling out of the chuck.

When it closes on the drill and the drill is in straight then hold the chuck as tight as you can while squeezing the trigger to make the jaws close very tightly on the drill. If you have very tender hands you might want to use gloves.

To get the drill out put the switch in reverse, hold the chuck very tightly, and squeeze the trigger to open the jaws off of the drill.

Nov 28, 2009 | Black & Decker Drills

1 Answer

How do I change my black & decker electric drill to go in reverse or forward? As you can see I'm tool challenged. Kathleen


The switch near the trigger that toggles left or right controls that.

Good luck with your project, Kathleen.

Oct 02, 2009 | Black & Decker 3/8" Variable Speed...

Not finding what you are looking for?
Black & Decker Compact Power Screwdriver Logo

Related Topics:

584 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Hand Tools Experts

yadayada
yadayada

Level 3 Expert

66563 Answers

Don Numinen
Don Numinen

Level 2 Expert

55 Answers

kakima

Level 3 Expert

100340 Answers

Are you a Black & Decker Hand Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...