Question about Epson Aculaser C1100 Printer

1 Answer

Epson Aculaser C1100

DDDD

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Ring EPSON technical support and get them to talk you through the situation.

Posted on Jul 02, 2008

2 Suggested Answers

  • 5 Answers

SOURCE: Epson Aculaser C1100 E537

Hi there

This suggests a fuser error. This is the hot unit at the rear top of the machine.

Steps are as follows:-

1. Open COVER FUSER.
2. Draw out the COVER RH boss from the hole on COVER FUSER while pushing
COVER RH outward, and remove COVER FUSER.

After removal check coninuity across heater lamp amd thermistor terminals. If either shows anyhing more than 13 Ohms then you need to replace your fuser unit.

Anything more than that requires hands on technical expertise.

Good luck

ivorpits

Posted on Dec 20, 2008

  • 1 Answer

SOURCE: epson aculaser c1100 not printing right hand edge

The problem may well be that the drum needs cleaning. There is a plastic flap on the rhs of the machine. Open that and you can pull a long lever out. You also need to let down the front cover and pull out the lever on the right hand edge that faces you. Then extend the long lever at the side as far as it can go and push it in and out a few times. This should solve the problem. Put the front lever back and close the cover. It took me ages to find this - Epson are not good at highlighting it,.

Posted on May 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Epson AcuLaser changé photoconducteur et faire passer le message d'erreur «installer photoconductr"...et le photoconducteur pour ma nouvelle Epson Aculaser C1100 et je reçois le...


salut ;
ce message apparait lorsque le detecteur de photoconducteur est bloque avec du toner, desinstaller le photoconducteur ; nettoyer le detecteur situe a l'interieur.

Oct 19, 2010 | Epson Aculaser C1100 Printer

2 Answers

Espon aculaser c1100 service req e511


Error E511 is due to ur photoconductor.. the black transfer belt is out of position... it can be corrected if you know how to open up the photoconductor unit...

May 14, 2010 | Epson Aculaser C1100 Printer

1 Answer

I HAVE E511 PROBLEM ON THE C1100


The "Service Req E511" error message means that part of the photoconductor unit called the transfer belt is not being detected. Please see the following Epson article which may help. http://www.epson.co.uk/Store/Printers-and-All-in-Ones/Epson-Aculaser-C1100/Drivers-Support?target=article&extn=.html&articleId=1319

Jan 29, 2010 | Epson Aculaser C1100 Printer

1 Answer

I've a notice in epson aculaser 1100 lcd (service reg E511)


The E511 error for your Epson Aculaser  in most cases means that its motor has malfunctioned or something is preventing the motor from working properly.

Jan 26, 2009 | Epson Aculaser C1100 Printer

1 Answer

Epson Aculaser C1100 E537


Hi there

This suggests a fuser error. This is the hot unit at the rear top of the machine.

Steps are as follows:-

1. Open COVER FUSER.
2. Draw out the COVER RH boss from the hole on COVER FUSER while pushing
COVER RH outward, and remove COVER FUSER.

After removal check coninuity across heater lamp amd thermistor terminals. If either shows anyhing more than 13 Ohms then you need to replace your fuser unit.

Anything more than that requires hands on technical expertise.

Good luck

ivorpits

Dec 20, 2008 | Epson Aculaser C1100 Printer

2 Answers

How to install toner chip on epson c1100


The toner chip is situated on the end of the toner cartidge - it's a circle, about 1.5cm in diameter.
They may have given you a new housing, in case you damage the one currently on your toner, when you try to remove it.

Nov 15, 2008 | Epson Aculaser C1100 Printer

1 Answer

EPSON C1100 JAM ON MP E SITE


Solution to this can be found here: http://www.tradebit.com/filedetail.php/2366766-epson-aculaser-c1100-jam-mp-e-countermeasure
The printer has a modification kit for this error which is caused by a weak solenoid

Nov 09, 2008 | Epson Aculaser C1100 Printer

1 Answer

Epson Aculaser C1100


I got the info through an Epson Eng I know. You should be able to get a replacement item by contacting Epson directly.

Sep 01, 2008 | Epson Aculaser C1100 Printer

Not finding what you are looking for?
Epson Aculaser C1100 Printer Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Printers & Copiers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Cindy Wells

Level 3 Expert

4759 Answers

Are you an Epson Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...