Question about Husqvarna Craftsman 36cc, 16 In. Gas Chain Saw

Open Question

Craftsman gas chainsaw 358.351600 I changed chain. lost half circle clip trying to get it on, bought new one cannot get it on. Is there a secret to getting it on?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

hunter19_46m
  • 7482 Answers

SOURCE: need to know about fuel

Hi arisaleman...
This drawing is how most chainsaws,weedeaters,and most 2 cycle small engines fuel systems are run.
Please take time to rate me


hunter19_46m_0.gif

Posted on Sep 10, 2011

dennisgladx
  • 52 Answers

SOURCE: craftsman chainsaw ps00376 2.0 cubic inch oil/gas ratio

Hi rbv1222,

40:1 is the ratio.

40 parts Gas to 1 part oil.
3.2 oz of oil per gal gas.

Glad to be of assistance. Please rate the solution because I can learn from your rating.
Thank you

Posted on Nov 09, 2008

dontbother10
  • 2220 Answers

SOURCE: Husqvarna chainsaw 440e - enough chain lube?

That seems low to me. Page 15 in your manual is the only oil discussion I found. Usually there is an oil pump adjustment reference somewhere. I didn't see one beyond return it for service on page 15. Are the chain and bar hot after cutting a while? I recommend you not get a longer bar without an oiler adjustment. I think the hand of the EPA has been here.

An IPL (exploded parts list) for a 440 can be found here:
http://weborder.husqvarna.com/order_static/doc/USA/2009/I09000/I0901018.pdf
There is no oiler adjuster listed. HTH
Lou
Might be a good idea to copy the IPL,

Posted on Oct 07, 2009

Testimonial: "thanking you"

  • 70 Answers

SOURCE: 16" craftsman chainsaw primer pfoblem

Check the condition of the fuel line and filter in the tank and to the carb and primer.Today gas and time will soften them allowing them to become blocked or leak.Replace if needed.

Posted on Oct 24, 2009

dontbother10
  • 2220 Answers

SOURCE: I BOUGHT A NEW CHAIN FOR MY CHAINSAW AND IT WON'T

I think Stihlfan is correct. Please look closely at Chain Installation, I wager the orientation of your bar is reversed.
http://www.fixya.com/support/r4146814-chainsaw_chain_installation
HTH
Lou

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the factory settings on a craftsman 2.3 chainsaw and to adjust carburetor


tighten the two air screws to just tight then slacken them to one and a half turns start the engine and adjust the low screw until tick over then open the throttle to full and adjust the high screw if it cuts out take the high screw to one turn and try that then adjust from there

Oct 28, 2013 | Husqvarna Craftsman 36cc, 16 In. Gas Chain...

1 Answer

I have a Craftsman 18"


I lost you but you do need a special tool for the clutch removal.Sorry I lost you.........Darryel (dleemacc)

Jul 31, 2011 | Craftsman 38cc 16" Gas Chain Saw

1 Answer

I have only used my saw a handful of times and it has always done this since i bought it new at lowes. It wont lube the chain with oil and gets vry hot at the clutch it will go through a tank of gas to a...


I have the exact same saw. I bought it new 6 months ago also from lowes. It has the exact Same problems you are describing. It does not appear to be oiling the chain enough, the Chain is visibly dry,very hot , and dulls quickly. It uses a half tank of oil to a tank of gas. I am Also in search of an answer.

Oct 20, 2010 | Husqvarna 350 18 Inch Gas Chainsaw 52CC...

1 Answer

Chainsaw idles, goes to high speed for a few seconds but dies under load. Sometimes cuts half a limb before it dies. Changed gas and then changed spark plug. Still dies.


have you looked at the filter in the tank? get a wire hook fish around in the tank it should be on thend of a fuel line inside the tank

Aug 22, 2009 | Husqvarna Craftsman 36cc, 16 In. Gas Chain...

1 Answer

Craftsman chain saw only runs short time


Craftsman is made by Poulan.
How old is the saw? Have you checked for split fuel hoses? Change the cc to model number (2.2cc Craftsman is often Model 2200 Poulan) and try to find an IPL http://www.ordertree.com/cms/illustrated-parts-list/9788.html. This will show hose routing. As a last resort you may try the "Chainsaw forum here http://www.arboristsite.com/. These are good guys but you will be flamed for buying a homeowner saw.
Lou
I'd put the filter back on.

Aug 09, 2009 | Poulan Garden

Not finding what you are looking for?
Husqvarna Craftsman 36cc, 16 In. Gas Chain Saw Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

Phil Walker
Phil Walker

Level 3 Expert

605 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...