Question about Yamaha YSP-800 System

1 Answer

Reset system I was jamming the other night on my system, and all of a sudden--no sound. I think one of the sensors kicked the unit off as a safety measure, and I need to reset it. Can someone tell me how to reset my YSP-800? turns on but no sound

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 183 Answers

Dear Customer,

Check it out first power lines is it ok on stabilised,

than check at minimum amplification ,

Amplifier must not have more than
82 W total power:
2 W x 21 + 20 W x 2

check it with passion & care,


Posted on May 13, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

D1000 closes holding wall button only, sensors clean and same, bypassed them it still did it, remotes don't work

This sounds like a problem with the safety sensors; either due to a blocked path between the safety sensors, condensation, mis-alignment, dirty eyes, loose wires at the sensors or at the motor head, or just bad safety sensors. When the infra-red safety sensors are malfunctioning, usually one of the sensor lights will be blinking or a blinking red light will show rather than green or amber. The sensor lights need to be solid and not dim or flickering.

When the sensors are at fault, the remotes cannot close the garage door; they can only open it. You may find that the door will only move an inch or so in the close direction. When this happens, your garage door will only close by holding down on the wall button until the door fully closes. This method is the only way to override the safety sensors and close the door. This is also a direct clue that the safety sensors are the problem.

Also, try unplugging the garage door opener and re-plugging the unit back into the outlet. This can act as a reset and may reset the sensors. If none of this works then you may have to replace the sensors or possibly the logic board inside the motor unit.

Aug 20, 2017 | Building Materials

1 Answer

My Carrier 58STA quit. I killed the power and then started it after a minute or so. It started working fine after that. It worked fine for another 2 1/2 days and then it repeated the process.

this sounds to be a tricky kinda sensor fault , that's shutting it off , this is why it restarts when pwr is reset (resets safety shutdown) also this model is known to have control board faults due to control board being mounted right on blower housing (vibration) id have a tech ck it out they should be able to see if its a flame sense sensor or contrl board error

Dec 21, 2016 | Carrier Refrigerators

1 Answer

What is causing intermittent lack of power?

seems like it's going into limp mode intermittently i would try cleaning crack shaft sensor. or replace.

Apr 05, 2016 | 2003 Hyundai Elantra

1 Answer

How can I fix a jammed Ryobi miter saw blade?

Probably go a piece of wood between black and safety cover. Unplug from power before checking

Apr 30, 2014 | Ryobi 18 Volts Cordless Miter Saw 18v P551

1 Answer

I have an oil fired aga the oil will not come throw to the burner

see the following steps:
f the burner doesn't run, set the thermostat a few degrees higher than normal to see if it comes on. If it still doesn't come on, check switches, and breakers and fuses (see the Electrical Service Panel Fix-It Guide). If the unit has a reset button, press it. Also oil the motor at any oil ports (see below). If the unit doesn't want to start and run, first check the c to make sure that the ignition is getting power. If there is power, check the built-in safety controls (see below) that may turn the system off if they perceive problems.
If the burner cycles too often, replace the filter (see below). Also, oil and adjust the blower (see the Forced-Air Distribution Fix-It Guide).
If the burner runs but won't fire, make sure the oil valves are open and that there's oil in the tank. Check the tank level with a clean stick.
If the burner smokes or squeals, shut off the unit, let it cool, and fill the oil cups. Recheck them after the motor has run for an hour.
If the chimney smokes even after the flue has warmed up, the unit is wasting fuel; call for professional repair.
Safety Controls
Oil furnaces and other heat systems include safety devices that monitor operation and turn off the unit if something goes wrong. In some cases, the safety device can be the problem.
If you encounter an operating problem with an oil furnace, first reset the safety and try again.
If the burner kicks off again, shut off all power at the electrical service panel ; the burner motor and ignition may be protected by separate fuses or breakers.
If the sensor has a photocell, wipe it with a clean rag or tissue and see if the furnace starts.
If the safety is a stack switch mounted on the flue, remove the screw holding the unit to the stack, slide it out, and wipe off the sensor.
If the furnace won't start after three tries, seek professional assistance. Unburned oil can accumulate in the combustion chamber and "flash back."


Jul 31, 2012 | Heating & Cooling

1 Answer

How can i manually reset the computer on my 99 chevy silverado 1500 4x4? my oil pump is weak and it has a dry start and when i started it this mornin i think it kicked the knock sensor and shut my motor...

The knock sensor will not cause a no-start. The knock sensor only retards the timing when the engine is running. If the starter is not working we need to check the battery voltage, battery cables, starter, engine ground, neutral safety switch, ignition switch, security system. These are the only things that can cause a no crank.
If you really have the urge to clear your computer disconnect the negative battery cable for 10 minutes.

Mar 10, 2011 | 1999 Chevrolet Silverado 1500

2 Answers

When slowing down approaching a light the brakes work normally until just before stopping when the ABS kicks in and the brakes pulsate. Help!

One of the speed sensors are bad. It might be hard to tell which one unless you have a scanner. Do you ever see an abs light on?

Jul 18, 2010 | 2003 Chevrolet Suburban 1500

1 Answer

Samsung 350N seizes up during warm-up cycle.

I think I have fixed this. The waste toner container was fairly full.This problem was initially intermittent and then persistent. Opening the printer cover and closing it was enough to shake the toner clear of the sensor until it became so full that shaking it made no difference. There was nothing to differentiate this problem from a paper jam so it was just luck that I checked the waste container. A quick short term fix was to tilt and tap the container to clear the sensor window, but the risk is that the container will overflow. Samsung tell you to replace the container (for about $AUD25) but it can just be emptied. I used a vacuum cleaner to **** out most of the toner and then washed out the rest with soapy water. I rinsed it with a solution of about 20% alcohol and then left it to dry over night. No problems since.

Jan 30, 2010 | Samsung CLP-350N Laser Printer

1 Answer

False Paper Jam

Unfortunately, I think that the sensors are beginning to fail, and that is the result of a faulty sensor. How old is the printer? If I was you I would call HP and talk to them.

Ryan Frame
Creative Energy Associates Technical Center

May 11, 2009 | HP Officejet Pro L7590 All-in-One InkJet...

Not finding what you are looking for?
Yamaha YSP-800 System Logo

Related Topics:

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Players & Recorders Experts


Level 3 Expert

5318 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

74990 Answers

Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides