Question about Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

What is code F 51 - Kenmore Elite Oasis 27052 Top Load Washer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,619 Answers


Hi



Thanks for using FixYa and I am sorry to hear whatever happened. Error
F 51 flashes when there is a motor rotor position sensor (RPS) failure. Please follow the step by step instructions to resolve this issue: This test checks the wiring to the motor and rotor position sensor; and the motor and rotor position sensor themselves. NOTE: Drain water from tub.

1. See Activation of Manual Diagnostic Test Mode, and check the motor and electrical connections by performing the Agitate and Spin tests under Manual: Motor. The following steps assumes that this step failed.
2. Unplug washer or disconnect power.
3. Check to see if basket will turn freely. If basket turns freely, go to step 4. If basket does not turn freely, determine what is causing the mechanical friction or lock up.
4. Remove the console to access the machine/ motor control assembly.
5. Visually check that the P5 and P10 connectors are inserted all the way into the machine/motor control. If visual checks pass, go to step 6. If visual checks fail, reconnect P5 and P10 and repeat step 1.
6. With an ohmmeter, check for 16 ohms resistance at the P5 connector between pins P5-1 and P5-2, and also between pins P5-1 and P5-3. Also measure the resistance at the P10 connector between pins P10-1 and P10-7 and verify that the resistance is within the range. If the resistance is correct, go to step 11. If the P5 connector resistance is much higher than 16 ohms, or the P10 connector resistance is out of range, go to step 7.
7. Tilt machine forward to access the bottom of the machine and the drive motor area. Remove the motor bolt, then the motor cover to access the motor connections.
8. Visually check the mounting bracket and electrical connections to the motor and rotor position sensor board. If visual check passes, go to step 9. If visual check fails, reconnect the electrical connections, reassemble stator and motor cover and repeat step 1. With an ohmmeter, check for continuity between all pins on the P10 machine/motor control connector and the motor rotor position sensor (RPS) connector. If there is continuity, go to step 11. If there is no continuity, replace the lower machine harness.
10. With an ohmmeter, check for continuity between all pins on the P5 machine/motor control connector and the drive motor connector. If there is continuity, replace the drive motor. If there is no continuity, replace the lower machine harness.
11. The drive motor and lower harness are good. Replace the motor RPS board and perform the Diagnostics test in step 1 to verify repair.
12. If the Diagnostics motor test in step 1 failed, then the machine/motor control has failed: Unplug the washer or disconnect power. Replace the machine/motor control assembly. Perform the Motor Diagnostics in step 1 to verify repair.


Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Posted on Sep 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What repairs should be made for diagnostic codes 13 and 51 .


which engine, that be first. no? look at it and what is it?
ill pretend 4.0L I-6
old car, with OBD1. code 13 and 51 are fully covered in the FSM.
ever seen and fsm? login to aldata.com and read.
and is discussed , infinitely on all jeep forums on the net. endless.
google that.? yet?
here ill google for you
i google jeep 13
http://www.allpar.com/fix/codes/faults/code13.html

and jeep dtc 51
http://www.allpar.com/fix/codes/faults/code-51-52.html


13 would cause 51s so,...... work that.

Oct 02, 2014 | 1994 Jeep Grand Cherokee

2 Answers

What codes are these to 1994 geo panel blinks two numbers 42 and 51


Ignition bypass error.42,incorrect MEM-CAL 52.

Aug 24, 2014 | Cars & Trucks

1 Answer

My problem is malfunction code 51 and if I have bad convertor does this result code 51ode


Code 51 is a lean code and is not caused by a converter most likely a vacuum leak is causing this problem if the engine seems to run fine inspect vacuum hoses and intake gaskets for leaks or breakage

Dec 10, 2012 | 1997 Jeep Grand Cherokee

1 Answer

Need tofind out code 51 for 1997 jeep grand cherokee 4x4


Code 51 is ( Right Rear Fuel System Lean ) A lean air/fuel mixture has been indicated by an abnormally rich correction factor. Did you get this code by the flashing check engine light?

Sep 04, 2010 | 1997 Jeep Grand Cherokee

2 Answers

Have an Error 51 on Brother MFC-210C all in one printer?


I can help you with your Brother MFC-210C error 51 problem.

Error 51 refers to a paper jam error.
Clear the paper jam to clear the error code.
If the error code will not clear after clearing the jam, resetting and powering off, the printer may require service.

I hope that helps.

Aug 30, 2010 | Brother MFC 210C All-In-One InkJet Printer

1 Answer

Code 51 for chevy van g20 1990


code 51
oxygen sensor voltage indicates lean engine operation

this code lights up check ingine light on vehicals with special california emission controls

Aug 21, 2010 | Chevrolet G20 Cars & Trucks

1 Answer

I have code 51 flashing. Where is the air bag diagnostic module located?


Hi, the code 51 flashing means that the internal fuse is blown and the short to ground is no longer present. If the short to ground returns, the code will change to 13 (air back circuit shorted to ground) or 14 (primary crash sensor circuit shorted to ground), but it will only flash 13 or 14 when the short is present. If the code remains 51, then first find and repair short before replacing the diagnostic monitor (what people call air bag module).
Take care

Aug 03, 2010 | 1994 Mercury Grand Marquis

1 Answer

Car problem


51= O2 sensor lean,
55= end of codes list

Jan 29, 2010 | 1991 Chrysler LeBaron

3 Answers

Hi, I get code number 51. Not sure what I can do to find and fix problem. Thanks


Code 51 is Wide Open Throttle Problem. You need to replace your fuel filter, possibly drain fuel tank and clean fuel pump pre-filter. That is in the fuel tank. If you have the cash, I would replace fuel pump while inside the tank.

Sep 25, 2009 | 1994 Chrysler LeBaron

Not finding what you are looking for?
Kenmore Elite Oasis 27052 Top Load Washer Logo

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2180 Answers

fordexpert

Level 3 Expert

5520 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...