Question about Intel Motherboard

1 Answer

Is 845 glad mother board support 250gb hdd sata drive

Hi,
can any one inform me what is the possibility of mother board accepts(845 glad) to 250gb sata dard disk.if yes let me know the details.

regards
mravokumar2003@gmail.com

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 271 Answers

You only need a motherboard with a sata (RAID connector).

Posted on May 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My motherboard is intel d845gvsr tell me how can i install sata hdd with this mother board and how many gb sata support


For sata HDD Your can connect your sata HDD using IDE to SATA cable. Intel 845 can support upto 320GB only.
ykeen_0.jpg

Mar 17, 2011 | Intel D845GVSR Motherboard

1 Answer

Hdd detecetion proublem on 845 motherboard


845 chipset dont support sata devices and this is common problem that if unsupported device is forcefully bieng tried to work its goona happen sata support started from865 chipset u are lucky that ur hdd is getting detecting

Jun 11, 2010 | Motherboards

1 Answer

Sir i have intel 965ry mother board i want to connect 3 250gb sata hdd s but the system as slowly why


dear friend
Because it must recognise the three hard disk of 250GB, and memory is not frequent to working with large amount hard disk.
It is better to work with only one hard disk of 250GB. According to mother board requirement it supports up to 500Gb Hard disk but single hard disk of 500GB.

Jun 27, 2009 | Intel D845GVSR Motherboard

1 Answer

HI i m posting the same problem onceagain with the trouble shooti


You could try flashing to the latest bios and disabling SATA RAID, disabling IDEs including bus master if u dont use any.

Apr 19, 2009 | MSI Mother Board (MSM865PEN2V) Motherboard

2 Answers

New SATA Hdd detection problem


Have you checked in the bios setup of the motherboard if your SATA ports are enabled?

Let me know if you need further assistance.
Regards,
Graemevm

Apr 19, 2009 | MSI Mother Board (MSM865PEN2V) Motherboard

3 Answers

Sata Port Connector is not avtivating


I had the similar problem with the K8MM-V Motherboard. I has been using a PATA HDD. I need to intall a 250Gig Seagate SATA HDD. Despit all the Bios Configs the PC Could not detec the HDD. Untill i Put a Jumper on the HDD  limiting the SATA HDD to 1.5gig of OS instead of 3gig. Look at the Label of your HDD

Oct 28, 2008 | MSI K8MM-V Motherboard

1 Answer

Add sata HDD


Hi,
Make sure the power cable of SATA hard drive is properly plugged in or not.. It is possible.. Try with SATA 0..
Thank you........

Aug 30, 2008 | EliteGroup (ECS 915PL-A2) Motherboard

1 Answer

ASUS K8V-MX Motherboard with 250GB SATA HDD and 250GB IDE HDD Problem


Hi LP,
I’ am very familiar with ASUS motherboards. I am thinking you have posted two questions or more referring to the,
ASUS K8V-MX board. When you sign into you're FixYa account you than need to click on you're profile. Within you're profiles are the questions you have posted. Click that question to add or see the expert's answer. If you need another question (about the same item) re-post within that same question. You can even copy the link to an older post & past that link into you're next question. (Than I can read you're last question & my responce).
LP you have me all mixed up. I'll answer the question you have posted above. In the future please provide you're old post so I understand better.

There is nothing wrong with IDE 250GB drive or the SATA drive.
The problem you are haveing is setting the correct settings.

The ASUS K8V-MX can support two serial ATA SATA drives. The SATA drive's can only run at 1.0 version. 1.5GB transfer speed & not SATA II, the 3.0GB speed.

How to setup the SATA drive?
Please disconnect any other drives (IDE) & a second SATA drive that may be connected to the system. Except the CDROM drive.
Using you're manual the SATA drive should be connected to SATA1 port. Page 1-24 in you're manual.
Put you're windows CD into you're CD-ROM drive & boot the PC. You will see, Press any key to boot from CD... (press any key on your keyboard). Windows will start to install. Durring installation of windows the system will restart. You will again see, Press any key to boot from CD... (DO Nothing)!
Just allow windows to conintue on its own. Windows will continue to install it's self. This will happed once again, & again do nothing. Windows will finish installing it's self.
After windows has finished, load the ASUS CD into you're CD-ROM drive & install it's driver software. Restart the PC.
You must register windows. Do so.
Than update windows through windows update service. (This will take some time to complete). (Do not install service pack 3).
If you have an IDE drive 250GB in size & you installed windows on it. You must erase the drive or it will conflict with you're new installation on the SATA drive. To do this, look on the IDE drive & you will find a large white sticker. Printed on there is instructions of how to set the drive pin. Set the drive up as a slave drive. (This is only temporary).
Power off the PC & unplug the power cord. Connect the 250 IDE drive's power cable & data cable. Plug in the power cord to the PC & turn on the PC. Windows will load. Right click once on the start button & slide up to & left click on Explorer.
Find the 250 IDE drive, it should be drive letter D or E. Right click the proper drive letter & format the drive.
( Do Not format, Local_Drive C:\ ). Once the format is complete, power down the PC by clicking on the start button & click turn off the computer. Once off, unplug the power cord. Change the pin on the 250GB IDE drive to Master with a slave. Take the 40GB drive & change it's pin so the 40GB drive is a slave.
Connect the 250GB drive to the end of the IDE data cable & connect the 40GB drive to the next connector of the same IDE data cable. Re-check all power cables & data cables for good connections before closing the case. Plug the power cord in & power up the PC. Everything should run just fine.
Setting the pin for you're IDE drive's can be very confusing. Click on the link below. This will give you an idea of how to set you're pin for a master drive, master with a slave drive. If you post the name ST****** of you're two drives I can post the correct pin locations from Seagate's web site.
http://www.seagate.com/images/support/en/us/mxo_ata_jumpers.gif

Have more questions about this post?
Good luck!
Mike

May 21, 2008 | ASUS K8V-MX Motherboard

5 Answers

250gb sata hard disk to 845 glad mother board


Hello all. I have the same issue. My MB is 845G [P4 2.4 Ghz] and SATA harddisk I need to install is Seagate 250 GB Baracuda with 3.0Gb/s interface, I belive which makes this HD as SATA II. So for this motherboard should I prefer PCI cards which support SATA II over the supports SATA I [these are cheaper].

Thanks so mcuh!!!

May 12, 2008 | Motherboards

1 Answer

Mother board Intel p-4 can be converted into D.865 it is possible


D-845 is not updatability to become D-865 that was already design on that model of motherboard.

Please don't rate me Inappropriate if you don't like my solution or rate me SOLVED if you accept the reality. Thanks

Nov 24, 2007 | Intel Motherboard

Not finding what you are looking for?
Intel Motherboard Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Tony

Level 3 Expert

2598 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Are you an Intel Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...