Question about Audio & Video Receivers

1 Answer

Some of the led's are burnt out on my alpine cdm-7874. is this condition serviceable?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 137 Answers

Could be loose connection only. leds don't usually burn out. they just fade in time.

Posted on May 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alpine ine-z928hd problem with software update


Be sure to format the memory stick using fat or fat32.

Apr 16, 2014 | Alpine INE-Z928HD - 8" In-Dash Navigation...

1 Answer

I'm not quite shore how to connect speakers through rca cables can some body please tell me where to plug the speakers into on the back of the gemini cdm 3610


Speakers don't generally use RCA cables. AMPS and other electronic components do. Have you peeked at the manuals?

Apr 16, 2011 | Audio & Video Receivers

1 Answer

I have a Pioneer VSX-517K that does not powers up. I also do not get the standby led to light up. The fuses are ok and the stand by voltage is 5V. I do not understand the connections ACRY or ACWP and...


There Is A Little Thyristor On The Side Of The Main Power Board look real close youl see it its on the green back side mines burnt to i cant figure out the part # to change it because its burnt if you have any luck ost it please

Oct 19, 2008 | Pioneer Audio & Video Receivers

1 Answer

My Alpine CDM 7871 produces no sound other than through the pre-amp outputs. As as a result the only sound I am receiving is from the sub-woofers in the trunk. None of the speakers within the cabin of the...


Your problem is the amplifier IC inside the unit. It is attached to the heat sink and soldered onto the main circuit board. If you have a soldering iron, solder, and solder wick (to remove solder from bad IC) you could do this repair pretty easy. You would need to disassemble the unit and remove the solder from the IC, then remove the IC from the heat sink and attach the new IC to the heat and put it back into the board and then solder all the pins of the new IC back onto the main board. After that, just put the unit back together just the way you took it apart. Just pay attention to where all the screws went and make sure you get them all back in the right places.

If you do not have the soldering equipment and are not comfortable with your soldering skills it would be better left to a service center to do this. Just about any service center would be able to do this repair for around $100. That should include the part and the labor. The price will depend on the service centers rates, but it is an easy repair that would require less than 1 hour of actual labor. Most shops will charge a minimum of 1 hour labor even if it only takes 15 minutes.

I have been repairing car audio equipment for over 18 years and can assure you that this is the problem you have, it is the typical symptoms for a bad amp IC.

Feel free to ask any other questions by just posting back on this thread.

Dave

Sep 20, 2008 | Audio & Video Receivers

1 Answer

Alpine cda-9815rb


I solved this problem by calling Alpine Electronics customer services.

Apr 21, 2008 | Audio & Video Receivers

1 Answer

My ALPINE radio says that is i pod ready. how does that work


Your Alpine is Ipod ready meaning once you get the Ipod cable you can control an Ipod through your radio. It plugs into the back of your radio and then the other end you plug into your Ipod. You can probably buy an Ipod cable from where ever you bought your radio or any other Alpine dealer. I hope I could help.
-Andrew Hawkins

Apr 10, 2008 | Audio & Video Receivers

1 Answer

Alpine mrdm1001


Probablemente los IC amplificadores de audio esten dañados.

Mar 25, 2008 | Audio & Video Receivers

5 Answers

NAD 705 out if order


This seems to be continuin problem with those. Not sure of exact fix yet, but believe it is just a fuse or bulb that needs replaced.

Sep 01, 2007 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68352 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...