Question about Dewalt DC927KL Heavy Duty 18 Volt Cordless Hammerdrill

1 Answer

HAVING PROBLEM WITH DEWALT BATTERY CHARGER DE9108 ,NO VOLTAGE AT OUTPUT TERMINALS,NO DIAGRAM,GOT KNOWLEDGE OF ELECTRONICS. HELP PLEASE. mcgarrytony@hotmail.com

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How can u tell went the battery is charger

Posted on Nov 19, 2012

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 13 Answers

SOURCE: i need a schematic circuit

GOOD LUCK! NOT EVEN AVAILABLE TO AUTHORIZED SERVICE CENTERS

Posted on Feb 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is the Dewalt DE9108 battery charger suitable for charging Ni-Mh batteries?


  • For Battery Type: Ni-Cd Ni-MH
  • Input Voltage: 110V-240V
  • Smart Charger for Dewalt 7.2V ~ 18V Ni-Cd Ni-Mh Li-ion Battery
  • For Brand: DEWALT
  • Color: Black
  • Brand New: A brand-new, unused, unopened, undamaged item in its original packaging

May 04, 2015 | Dewalt Drills

3 Answers

DW 911 radio works on mains power but not with battery inserted


Change the battery connector pcb board part# 5140019-41 12.07 on ereplacementparts.com

Dec 06, 2014 | Radio Communications

1 Answer

Need a circuit diagram of a dewalt charger DE9108-xe 7.2V-18V one hour charger type 1:Q 96307-12/15 OUTPUT : 2.6A 7.2-18.0V 46.8VA


Can you (carefully!) measure the volts across them with a load (battery) and then the current through them by disconnecting one end, and if the charger is still working OK then they are V/I ohms, choose nearest value. 10k sounds very high, are you sure they aren't 1 ohm or less?

May 21, 2014 | Dewalt 7.2-18.0 Volt One Hour Charger

1 Answer

Battery 14.4 v.dewalt


Even if you could press it in the charger, you would damage the battery bend repair. It even could explode. That is why they have different slots.

Mar 20, 2014 | Electronics - Others

1 Answer

1990 Dodge Ramcharger won't start. Battery output 12v, voltage across coil terminals 6v, voltage output at coil port to coil wire 6v, voltage of coil wire output to distributor 6v. Engine will c


There should be a small white ceramic block on the firewall - this component cuts the battery voltage from 12 to 9 volts for the coil and ignition system. It has 4 wires and is called a ballast resistor.
You may need a book with the wiring diagram to be able to test it. You should have battery voltage going in and something like 9 volts coming out.
You can also run a wire with a fuse from the battery to the positive side of the coil to check the system. Disconnect the factory wire from the coil first.

Jan 27, 2013 | Cars & Trucks

1 Answer

I have a Schumacker Model SS-51A-PE charger and was charging a boat battery when I heard a medium-to-loud pop. I checked the charger and realized there was no output. It hums quite loudly when plugged in...


Quite simply - the unit has suffered component failure - most likely more than one. Capacitors are the usual source of noisy 'bang' or 'pop' sounds, followed by diodes and bridge rectifiers. If you have some knowledge of electronics, you can attempt repair, but, if none, I suggest leaving possible repairs to someone who does.
The humming sound you hear is the transformer under stress, and, if left connected, it too will die.

Sep 21, 2010 | Schumacher 10 Amp Fully Automatic/Manual...

1 Answer

I HAVE DEWALT CHARGER DE9116.ITS OUT PUT VOLTAGE WITH OUT LOAD IS 51 VOLT.AND WITH LOAD IS 15 VOLT.THE BAATERIES BECOME VERY HOT WHILE CHARGING


check output voltage on charger label most chargers are not regulated so if it says 18 volt output it may put out 24 volts but if its putting out 51 volts it may have a short batteries will get warm but not hot replace charger

May 18, 2010 | Dewalt 7.2-18.0 Volt One Hour Charger

1 Answer

My dell inspiron 6000 wont charge but i dont think the battery is the problem. The powerlead also still has its light on so must be still working. Any suggestions?


Hi,


Could you check the output voltage of charger with multimeter? If you find output voltage then your charger is OK, Might be some problem with charging cirucit diagram of the laptop. If no output then replace your charger with new one having same specification.


Just remember to take your time and don't get nervous working on the computer. Please report back to the thread the results of your work.


Regards;
Hassan

Jul 12, 2009 | Dell Computers & Internet

1 Answer

De walt de9118 charger


when charger is plug in to ac it will blink once.normal voltage out for the unit in between 36v to 55 volt. the reading u have is normal.

Aug 07, 2008 | Dewalt 7.2-18.0 Volt One Hour Charger

Not finding what you are looking for?
Dewalt DC927KL Heavy Duty 18 Volt Cordless Hammerdrill Logo

494 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Jim Thurston

Level 3 Expert

670 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...