Question about RCA 27V530T 27" TV

1 Answer

27v530t How much would it cost to get the vertical adjustment fixed. Thanks Jeff

Posted by on

  • OUTLAW11JA May 12, 2008

    Thanks,

    Jeff

  • bridgetv Dec 23, 2008

    RCA 27r410t can't see scroll on news channels or scores on ESPN. Is there a way to adjust screen size or vertical display?



×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 131 Answers

Two replace a verticale ic which is common for verticale problem.. It requires replacing a part not adjustment . I charge at my office is around 95,00 dollars to 120.00 dollars.

Thanks doctor video

Posted on May 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No picture no sound


Most common cause is bad high voltage transformer and the sweep transistor just in front of it---only generic parts are available for this set--cost usually under 40 dollars but for a 27 inch (what is listed here) hardly worth fixing.

Jun 11, 2012 | RCA 27V530T 27" TV

1 Answer

Television has sound can change channels....but has no picture just a thin horizontal line in middle of screen


Hello
The vertical sweep section of your TV is faulty. It may be either to a loose solder points at somewhere in that section of to the fault with the vertical output IC. Check all the solder points on the vertical output section of your TV. It is best to resolder most of the suspected soldering points, by applying a little more solder, without making any solder bridge short in between adjecent solder terminals. If this does not help you, replace the vertical output IC with same type and number. OK.

Oct 21, 2011 | RCA 27V530T 27" TV

1 Answer

Horizontal width jitter after turn on, or picture gets wide and then back and forth!


hi there, seems you're encountering horizontal width suddenly adjusted by itself. i recommend you unscrew the back casing, clean the crt board a bit and look for the capacitor on the secondary output of the transformer voltage chopper. it has this diode series with the output and filtered with electrolytic capacitor. if you notice bulgy appearance replace it with same type and farrad rate. most of the times it is unnoticeable by just physical checking. Some are leaky and can be determined using capacitance tester. The supply of the Vertical IC is not stable cause by this capacitor. replacing most of the capacitor wouldn't cost you much. hope this helps, please rate and vote

Mar 26, 2011 | RCA 27V530T 27" TV

1 Answer

When i plug in the component cables I get a scrambled image


Hi,


This is caused by loss of vertical and/or horizontal synchronization of the scanning lines that produce the raster.
It is usually caused by a defect in the electronics section called the deflection circuitry.

You may be able to adjust it back enough to get it working if you can find the vertical or horizontal "hold" controls (they may be called by some other name). They are sometimes seen at the on-screen display section, sometimes on the front or back panel and sometimes inside the back cover. On newer sets it is factory fixed and there are no user adjustments. So, you might have to poke around until you find them.
If you cannot find them, or if you do find them and they don't adjust enough to lock in the picture then you will need servicing and the cost will be to replace the IC or transistor that produces the hold lock on the deflection system.


Please get back to us if you have any further query or else accept the solution.

Thanks for contacting fixya.com

Nov 01, 2010 | Sharp 27U-F810 27" TV

2 Answers

Turn it on i hear a click but no picture, about 10 seconds later the tv clicks again like it's turned off


Sounds like your tube is out. To fix it would cost more than the TV. Try to unplug it overnight and try agian. Post again when you try that and we can try something else.

Mar 17, 2010 | RCA 27V530T 27" TV

1 Answer

PARAMETERS FOR RCA


hold menue button in. push power once vol up once.vol up to76 ch to po1 po3  have fun.

Nov 13, 2008 | RCA 27V530T 27" TV

1 Answer

Gone haywire


Your circuit board has definately overheated. You have to send it into the manufactorer for a replace.

If this helps at all, please rate this a FixYa. - Evolution

Jun 09, 2008 | RCA 27V530T 27" TV

1 Answer

Adjusting vertical and horizontal


There is no adjustments on this model if horz is off i suspect a bad capacitor in around the verticle ic.


I fix a lot of these tv at my shop. cost is around 120.00 at our place.


I hope this helps thanks DOCTOR VIDEO

Apr 27, 2008 | RCA 32V550T 32" TV

1 Answer

Horizontal and vertical adjustments


sorry there is no adjustment for this .you probably have a bad component in tv


thanks Doctor video .

Oct 17, 2007 | RCA 32V550T 32" TV

1 Answer

Wide black bar on bottom of screen


I you know how to repair electronics its not a hard fix. The worst case would be the vertical output IC but im thinking th its nothing more then a capacitor in the verticle sweep circuit The average cost to repair this should be around 75 to 125 bucks. Good Luck

Jun 01, 2006 | Toshiba 32A60 32" TV

Not finding what you are looking for?
RCA 27V530T 27" TV Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68352 Answers

John mullen

Level 2 Expert

245 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a RCA Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...