Question about Garden

Open Question

The spark plug gap for a homelite textron chain saw 10563 A.seirial 700390366 VI super 2

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 10865 Answers

SOURCE: spark plug gap

hi kathy. this is an easy one. first of all you will need a spark plug gapping tool, about a dollar at any auto parts store. Your chain saw most likely calls for PLUG TYPE: Champion CJ6 SPARK PLUG GAP: 0.025 in. (0.63 mm).

Here is the website of a short video to show you exactly how to gap the spark plug. write back if you need any more info.

www.expertvillage.com/video/6078_spark-plugs-gap.htm

Posted on Feb 07, 2009

Ad
  • 323 Answers

SOURCE: The chain on my chain saw is slack.

The adjusting screw is usually found on the right side of the saw close to the bar, near the bottom. You will need to loosen the two nuts on the side that hold the bar tight. Loosen them until the bar lifts up and down (about 1/2") with your finger.

There should be a combination spark plug wrench and screwdriver that came with your saw. If not, use a slot screwdriverto tighten the chain while you hold the bar up with two fingers.

When adjusted properly, there should be no hanging slack in the chain when it is warm. It should rest just against the bar so that you can grasp it with gloves on and pull it toward you.

When it is tightened thusly, tighten the two side nuts while holding the bar up with two fingers. If you don't tighten the two nuts enough, it will loosen and the chain will have slack again shortly.

Remember that the hotter the chain gets, the looser it will be. Make sure your chains is getting plenty of bar oil. Never use regular motor oil.

Posted on Jun 08, 2009

  • 583 Answers

SOURCE: Homelite Textron chain saw UT 10403A ...need

25to 1 and .025 thou

Posted on Aug 06, 2009

hunter19_46m
  • 7482 Answers

SOURCE: spark plug gap for homelite

Hi idone8...
Set your gap using a round feeler gauge to .28 to .32
Please take time to rate me

Posted on Sep 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I set idle on my homelite super2 chainsaw


Homelite XL 2 Automatic Chainsaw - YouTube

? 6:12
https://www.youtube.com/watch?v=qk6nk-JQ-zg
Apr 20, 2012 - Uploaded by Alec Ulm's Busted Knuckles
Homelite XL 2 Automatic Chainsaw ... free to shoot me a question or comment and I'll do my best to answer as accurately as I can . ... Homelite SUPER 2 Chainsaw OILER REPAIR & TEST RUN - Duration: ... HOW TO ADJUST A Homelite Carburetor - Duration: 5:01. by smallenginemaster1 177,482 views.

How to Adjust the Carburetor on a Homelite Super VI Chain ...

homeguides.sfgate.com > Construction & Remodeling > Siding
Homelite Super VI chain saws are equipped with a Walbro HDC diaphragm, and ...Adjust the idle mixture screw and idle speed screws clockwise one-quarter turn at a ...Homelite Super 2 Chain Saw Oil Type · How to Replace a Carburetor on a .... MyRidevisit'Cars-My Ride'navigation-www'4 · Sell Your Carvisit'Cars-Sell ...

Need carb settings for Homelite chainsaw - My Tracto



Jan 03, 2016 | Homelite Garden

1 Answer

Homelite textron 104664


Unfortunately it's almost impossible to repair a leaking gas tank on a saw

Feb 20, 2014 | Garden

1 Answer

Need a manual for homelight textron super ez automatic chainsaw serial # 292740092


You can download then print your Homelite manual by going to www.homelite.com/service/product owners manuals the best way to do it is to right click on the material, left click save, put in in your Documents folder, then retrieve it to print if you actually have to hold paper. Good luck

Sep 23, 2011 | Homelite ZR10926 16 Chain Saw

1 Answer

Spark plug gap for homelite textron ut 10080c chain saw


Hi idone8...
Set your gap using a round feeler gauge to .28 to .32
Please take time to rate me

Sep 08, 2011 | Garden

1 Answer

I have an old homelite super xl saw and what i need to know is the high and low adjustments as well as spark plug gap


For the high and low speed jets turn all the way in and turn counter clockwise 1 1/4 turns to start with and continue a bit more until the saw runs a max speed(go by ear) and idling speed(idle down enough so chain does not spin while finger off triger). For the spark plug gap, go about 20 thousands of an inch. I hope this helps you out.

Jul 15, 2011 | Homelite Garden

2 Answers

The chain on my chain saw is slack.


The adjusting screw is usually found on the right side of the saw close to the bar, near the bottom. You will need to loosen the two nuts on the side that hold the bar tight. Loosen them until the bar lifts up and down (about 1/2") with your finger.

There should be a combination spark plug wrench and screwdriver that came with your saw. If not, use a slot screwdriverto tighten the chain while you hold the bar up with two fingers.

When adjusted properly, there should be no hanging slack in the chain when it is warm. It should rest just against the bar so that you can grasp it with gloves on and pull it toward you.

When it is tightened thusly, tighten the two side nuts while holding the bar up with two fingers. If you don't tighten the two nuts enough, it will loosen and the chain will have slack again shortly.

Remember that the hotter the chain gets, the looser it will be. Make sure your chains is getting plenty of bar oil. Never use regular motor oil.

Jun 08, 2009 | Homelite ZR10926 16 Chain Saw

1 Answer

Spark plug gap


hi kathy. this is an easy one. first of all you will need a spark plug gapping tool, about a dollar at any auto parts store. Your chain saw most likely calls for PLUG TYPE: Champion CJ6 SPARK PLUG GAP: 0.025 in. (0.63 mm).

Here is the website of a short video to show you exactly how to gap the spark plug. write back if you need any more info.

www.expertvillage.com/video/6078_spark-plugs-gap.htm

Feb 07, 2009 | Homelite ZR10926 16 Chain Saw

Not finding what you are looking for?
Garden Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

roeb

Level 3 Expert

537 Answers

john h

Level 3 Expert

12650 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...