Question about Dishwashers

1 Answer

Sears dishwasher reset code

Sears dishwasher, purchased in 2005 for $750. Starts blinking green like, book says call a repairman, will not run. There is a reset code which would allow it to run so I could try and clean it. Do you know what it is.

Posted by on

  • Chironsot May 12, 2008

    Junior:



    Model Number is 665-16269401

    Type 577.0

    Kenmore Elite Stainless Steel

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 117 Answers

Press hi temp and heat dry than hi temp and heat dry again in lass than 5 seconds
that should reset

Posted on May 11, 2008

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When switched on the pumpbutton stays red and the program selection does not want to move, one program remains blinking green. When door is closed pump starts running non stop. Cannot find any reset button


Thanks to a manual that was sent to me I understould I had to press the button P for a long time, that resets the machine. Thanks for your service! Carolijn

Nov 23, 2009 | Candy DFI Plan Built-In Dishwasher

1 Answer

Kenmore Elite Dishwasher model 16264 electrical fire


I contacted my lawyer who advised that I file a Civil Complaint against Sears so that is what I have done.

Feb 18, 2009 | Kenmore 24 in. 16264 Built-in Dishwasher

2 Answers

Kenmore 665 15899


To reset and run diagnosis on the model 15899100 Kenmore Dishwasher you need to press the following buttons on your front panel. Hi Temp, Air Dry, Hi temp, Air Dry. The sears service technician just left my house and used these codes to reset and run diag on my washer.

Hope this helps

Jan 05, 2009 | Kenmore 15899 Built-in Dishwasher

2 Answers

I have a Miele G841 SC Plus Novotronic Dishwasher. The Intake/Drain light is blinking and it won't work. What do I do?


I had a problem where my G842Plus dishwasher would run through the prewash and then the intake/drain light would start blinking and it wouldn't work. There would be water in the bottom of the dishwasher. After cleaning out various items to no avail, we called Miele technical support and they told us to reset the codes and then keep trying it over and over until it worked.
Here is how we reset the codes:
  • Turn dial to stop/off
  • Turn dial to Normal Plus
  • Press Start
  • Press power
  • Then press the start button for one second and let go

Sep 15, 2008 | Miele 24 in. Novotronic G842 Plus Built-in...

2 Answers

Blinking Green Light


Here's what I could find on the your error code:

A blinking clean light that flashes 7 times and cannot be reset, occurs when the electronic control does not detect a water temperature increase during the main wash. This could be an indication of a failed heating element, in line thermostat, electronic control board and/or wiring. This problem can also occur if the main wash pump becomes clogged and it not spraying sufficiently. I hope this helps you.

PS A faulty door latch can also cause this error code.

Jun 23, 2008 | Dishwashers

12 Answers

Kenmore ultra wash quiet guard 3 dishwasher problem


call sears, 1-800-4MY-HOME. They have a trouble-shooting department that will get rid of this problem. It is caused by water temperature being wrong at the start of the cycle.... blah, blah, blah. The representative will tell you to push a certain set of buttons in a certain order and that unlocks the dishwasher.

Sorry I don't know the sequence

Jun 08, 2008 | Kenmore 24 in. 15689 Built-in Dishwasher

2 Answers

Kenmore mdl 665.16034401 dishwasher


looking at your control panel there should be a option/clear button. push that button then the button to the right of that button back and forth untill all lights light up. that will start a test mode just let the test mode run once its done you should be able to run the dishwasher again

Nov 21, 2007 | Kenmore 16602 / 16604 / 16609 Built-in...

1 Answer

Green clean light keeps blinking


HI, Same thing happened to me today and Sears more than willing to charge me 200.00 for a 1 year service agreement. I found the answer on askmehelpdesk.com and the answer is: To reset a Kenmore Ultra Wash elite series dishwasher (stuck on clean) simply push heated/dry then normal wash and do the same thing again. Panel will reset itself and it hopefully will run normally again. Mine did and I am rejoicing! Julie

Aug 24, 2007 | Kenmore 24 in. 16302 Built-in Dishwasher

6 Answers

Kenmore 66516032400 Dishwasher


On another website, we found a reset code that works for our Kenmore, which I think is the same as yours. Hit Heated Dry, Normal Wash, Heated Dry, Normal Wash (one at a time, within six seconds).

Dec 05, 2006 | Kenmore 24 in. 16032 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

1,022 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

yadayada
yadayada

Level 3 Expert

70365 Answers

Brad Brown

Level 3 Expert

15111 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...