Question about Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint WF340 - wont complete programme

My machine will not run through a complete programme except the 'fast wash' setting, all other programmes get stuck with the machine full of bubbles. I can pump out and use the fast spin cycle to clear the machine and get clothes out. Any ides why? Have taken back off and cleaned some pipes but still have same problem
Thanks

Posted by on

  • gavloz1 Nov 16, 2008

    my machine won't complete a programme, i have to manually move it to the next cycle, it then sticks on rinse and spin fills up with water and spills out of the door.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Hi without looking at it i would think that the control board behind the timer knob has broken down these can quite pricey so shop around before you buy one,hope this helps.

Posted on May 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Aquacycle 1000 will not operate the 30 minute short programme. Advice please


i think there might be some programming fault .
so set the timer again or

start pause button

after having selected the required programme press this button to start the machine the corressponding pilot light stop falshig.
to interrupt the programme which is running depress the start/ pause button the corresponding light start to flash.
to restart the programme from the point at which it was interupteed
press the start/puase bitton again.

Jan 14, 2012 | Washing Machines

1 Answer

I have a problem with my hotpoint wf340 1400 spin when i put it on it washes but wont come off the wash cycle and will continue washing unless i stop it manually i then have to select pump out and then a...


it is either a broken wire to your heating element or the element itself is open circuit. when the water does not heat the machine will not move onto next stage of wash.

Feb 20, 2011 | Hotpoint Washing Machines

1 Answer

What does f-5 mean when flashing at me and won,t let me have my washing out the machine also washing really hot after a fast spin programme


if water is in drum then door wont open,drop drain hose to floor level into bucket to drain manually, then check filter or pump is it running ok if not is it stuck some thing in it , hot wash is cold water inlet ok or is this due to again faulty pump ...

Jun 25, 2010 | Hotpoint Aquarius WD640 Front Load...

1 Answer

My waashing machine a WMA62 Hotpoint comes on, you


that sounds like your heating element is o/c .... get your heater tested ..01179512835

Dec 30, 2009 | Hotpoint Washing Machines

2 Answers

Where can i get instructions on how to use my hot point aquarius wf340 washing machine


You can retrieve a complete owners manual if you go to the manufacturers site, under"support" you'll see downloads, type in your model # and it will come through as a type "pdf." file to keep on your computer forever.

Sep 07, 2009 | Washing Machines

1 Answer

Hotpoint BWD129 1200 spin - unwanted drying cycles


This is more a workaround than a solution. When you choose the washing programme (say "D") and push the on/off button, two lights will flash, the "door locked" and the "drying" one. Now turn the "drying programme" button until the "drying" light stops flashing (in my case, this is true when I set the drying programme to 40°C). Then start the washing mashine.

Seems like the function of the drying programme button has shifted against the settings written on the button...don't ask me why! Of course, no guarantee but works for me. Please let me know if it does for you.

Oct 13, 2008 | QuietLine WD-9900 Front Load Washer /...

1 Answer

WASHING MACHINE


Turn machine off and unplug for at least ten seconds

Then plug in and retry - according to Hotpoint that should solve problem

Mar 10, 2008 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Programme not moving on


This is not something like a belt or a motor then...It's probably the Logic in the control system.

Your best bet is have a hotpoint engineer diagnose it - and fit a new control module. To buy from hotpoint they range from 70 to 90 Sterling.

In england the call out is £90 and they actually don't charge for parts if the machine less than 5 years old.

Feb 25, 2008 | Hotpoint Aquarius WF210 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF000 Front Load Washer Logo

521 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

puggy666

Level 1 Expert

47 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...