How can i set up time my watch :sportek sp49281

To set the time on a Dakota one button watch, you will need to follow the instructions in the user manual that came with the watch. If you do not have the user manual, you can try the following steps:

1. Press and hold the button on the top right side of the watch: Press and hold the button until the time display appears.
2. Set the time: Use the button to set the time. The specific sequence for setting the time will depend on the make and model of your watch.
3. Exit the time setting mode: Once the time is set, you will need to exit the time setting mode. The specific steps for exiting the time setting mode will depend on the make and model of your watch.

It is important to note that the steps for setting the time on a Dakota one button watch may vary depending on the specific make and model of the watch. If you are unable to set the time using the steps above, it is recommended to refer to the user manual or contact Dakota customer support for assistance.
If you have a "his and hers" set of Dakota watches, the steps for setting the time on both watches should be the same. You can use the steps above to set the time on both watches.

[PDF]4 Button Digital Watch - Dakota Watch

https://www.dakotawatch.com/PDF_FILES/Digital.pdf

In normal time mode, Hold L2 for 2 seconds to alarm time set mode, then L2 again to normal time set mode, the second digits begin flashing. Press R2 to reset the seconds to "00", press R1 to switch to the minute digits. Press R2 to advance the minutes. Press R1 to switch to the hour digits.

how to set time in digital watch - YouTube

? 1:13
https://www.youtube.com/watch?v=4FmHYMeXbDA
Oct 26, 2011 - Uploaded by Vedant Sen
https://www.youtube.com/watch?v=u_H5I3H15R8 ... how to setyour digital watch {UPDATED} - Duration: 1:20. by Vedant Sen 3,424 views ... The 10 Greatest Wrist Watches of all Time REVISED FOR 2014 - Part 1 - Duration: ...

How To Change The Time On Most Digital Watches - YouTube

? 8:40
https://www.youtube.com/watch?v=kBvaePDtEUU
Jun 27, 2012 - Uploaded by Pitskate
How To Change The Time On Most Digital Watches. Pitskate ...How to change / set time on Armitron watch, 45/7004. - Duration: 2:02. by ...

you may find a manual from the manufacture. hold the mode button down 3-5 sec's. the hr should blink ,use the opposite side buttons to change the number, then press mode again mins blink change, do this and set hr,min,sec, am or pm? then date month,day yr. press final time and time should be shown with no blinking. you can also hold in all buttons and let beep 5 times it resets to zero defalt settings

I know it's been a year since this question was asked, but I was trying to find the answer today and finally figured it out. I thought I would answer for someone else.

I have a sportek SP1020ZEL. Pressing mode first and then alarm did not work for me. Pressing mode first on my watch only put it into the stopwatch mode, and then pressing the alarm button is for reseting the stopwatch. So I tried it the other way around, and it worked.

First, press and HOLD the alarm button (bottom right button) and then the mode button (bottom left button). My sportek doesn't show a little bell symbol, but I noticed that with one press all the days of the week showed and when I pressed again all the days disappeared. So I waited for the hour and found that when there is no days of the week visible the hourly chime is off. I don't think this works with all sportek watches but it is worth a try. (I did not try holding all the buttons for 5 seconds).

press in all buttons 5 sec or 5 beeps. sets to default settings. rest time and date

Thank you for contacting FixYa.

Set Digital Watch
1. Press and hold the "Mode" button on the right side of your Arnette digital watch for three seconds to change the watch's mode. Press and hold the "Mode" button repeatedly until flashing digits indicate that you have entered the watch's time-setting screen.
2. Use the top and bottom buttons on the left side of your Arnette digital watch to increase and decrease number values as desired.
3. Press and hold the "Mode" button repeatedly to exit the time-setting screen and return the watch to time-telling mode.
Set Analog Watch
4. Pull out the watch crown on the right side of your Arnette analog watch.
5. Turn the watch crown clockwise to adjust the hands of your Arnette analog watch to the appropriate time.
6. Push the watch crown back in when you are finished setting the time on your Arnette analog watch.

Best regards. Jewel

I am afraid you will have to contact Sportek at the following link:

http://www.sporttek.co.uk/info/Customer_Services.html

mcdevito75 here, the 2 buttons you need are the MODE and SET buttons, press Mode and see display flashing, now press SET to cahnge any of the settings, Hour, minute etc. press mode after each change, hour, minute etc. When all settings are done, press MODE for steady display.

Click on my profile (escapement), then click onTIPS AND TRICKS. There you will find plenty of watch manuals.