Question about Epson EMP S1 Multimedia Projector

1 Answer

All I get is a white screen. I replaced bulb, and nothing is different.

Please help.

Posted by on

  • nheagle Jul 19, 2008

    Thanks, I will try that.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Open the projector (6 inset screws on bottom) - carefully rermove the top (there are 2 wire sets attached: one for the speaker and one for the control panel) -- make sure all wire sets are properly seated -- i had one loose set -- reseated it, closed the projector and the thing wotks fine now. every repair facility i called didn't want to deal with the projector, and one person told me i ought to buy a new one

Posted on Jul 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2 epson EX31 projectors in our sanctuary that run the same image from the MAC. (song lyrics, slides, etc) Recently I replaced a bulb in one...and since then...the "White" levels in the projecto


If uniformity of the images is important, I would reccommend replacing the second bulb on the other projector with the same bulb, from the same vendor as you did the first. It may be too difficult to match them up otherwise (assuming the first bulb you bought isn't defective).

I hope this helps,
--Robert

Oct 29, 2014 | Epson EX31 Projector

1 Answer

Green power light blinks, nothing else happens, no bulb, no fan, nothing. Any ideas?


Power supply to he board is not adequate please vista a workshop.

Jul 06, 2014 | Optoma DLP Projector HD23

1 Answer

Dukane 7100HC The picture is dark. In a completely dark room. I recently replaced the bulb, but the picture was dark before I replaced the bulb. I've adjusted the brightness, but it just washes out the...


Turn the brightness up slightly and turn the contrast on the highest setting. There may also be settings to control wether your projectin on a wall or on a screen. Make sure these settings are correct to your setup.

Jan 25, 2011 | Dukane ImagePro 7100HC Multimedia...

1 Answer

My projection is in Black and White


I have seen this with a number of X1's and yes it will need to go into service and knowing what the cost of repairs was and the age of the x1 i would start looking for a new projector.

Jun 04, 2010 | InFocus X1 Multimedia Projector

2 Answers

Turn on, the screen is white, no menu, no words


need more info. make? model? dlp or lcd? just by what you said, i'd say main board; but the more info provided, the more accurate the diagnosis.

Nov 10, 2009 | Multimedia Projectors

1 Answer

Stuck in standby mode


The light bulb must be seated in perfectly, otherwise it won't see a connection and won't come on. take the bulb out, and make sure the connections don't have any dirt on it. Anything that can obstruct a connection. Give that a try.

Jan 09, 2009 | Sharp XR-10X Multimedia Projector

1 Answer

INfocus X1 does nothing after bulb replacement


first off, make sur you have the right lamp (sp-lamp-009, 2 white wires. not the sp-lamp-018, one white, one red. the wires are in different locations in the plug). if you don't hear the colorwheel whirring, that'd be the next step. however, you cannot buy just the colorwheel. infocus does not sell individual parts of the optical engine. but that wouldn't matter, seeing as how they don't sell the engine anymore. also make sure the lamp door is completely closed. there is a peg on it that activates a switch to let the projector know it's closed. if you remove the lamp and use a flat-head screwdriver to activate that switch, turn on the projector. look inside the lamp housing and see if the colorwheel spins. if not, i think you need a new projector. if it does, check the fans. they can be replaced.

Dec 19, 2008 | Apple InFocus X1 Multimedia Projector

2 Answers

Projects in black and white


It's probably the color-wheel problem. Maybe the color-wheel stucked because of dust and/or color-wheel sensor is covered with dust.

The simple way to check this, without reinstalling drivers or so, you just tap menu button on remote. If you will see only black-white user interface it is definitly color-wheel.

Good luck.

Nov 04, 2008 | Optoma H30 Multimedia Projector

1 Answer

Temp fault


check all the internal fans, if even one does not start, the projector will soon shut down!
every fan has three wires, one is the stop signal, that should stay "low" in most models.
this wire might be white or yellow, the red is + supply/blue or black is -supply(or gnd).

Sep 17, 2008 | Multimedia Projectors

2 Answers

A vertical white line on the projected screen


i'm having the same problem some one sugested changing the input tryed s-video and nothing i've taken mine apart and cleaned the color wheel thinking something was bloking light or the image the only thing i havent messed with is the lens area but i'm going to try it i'll let you know if it worked hopefuly someone can help us bcause now i'm stuck with a $300 bulb i hope i dont have to buy another 1

May 07, 2007 | BenQ MP610 Multimedia Projector

Not finding what you are looking for?
Epson EMP S1 Multimedia Projector Logo

Related Topics:

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Multimedia Projectors Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Are you an Epson Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...