Question about Vacuums

1 Answer

Problem putting on flat drive belt on Hover Vaccun cleaner model # U6434-900. Also how do I get the belt on? Do you have tool to help put the belt on.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The best way is to use an flat blade screwdriver. Attach to motor first than but screwblade into belt holding it aginst the brush holder drum and roll the brush forward inching the rubber belt onto the spendle that drives the belt

Posted on May 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it necessary to take the vacuum cleaner apart to change the belt on a Hoover Wind Tunnel Self Propelled vacuum cleaner, model UI6460-900? If so, how is that done? If not, how do you get the belt on...


To change the belts, make sure the vacuum is not plugged in. Lay it upside down and remove the screws holding the bottom plate on. Remove the bottom plate, pull the brush roll out noting how the belt goes so you will know how to put it back together. Especially how it goes around the idler pulley. Remove both belts, replace both belts, install the V belt onto the transmission first then around the brush roll and put the brush roll in place. Install the flat belt around the motor shaft and then onto the transmission pulley.

Feb 06, 2011 | Hoover Self-Propelled WindTunnel Bagless...

1 Answer

Please help! my cleaner will roll on a flat surface but when I try to roll on the carpet it is jumpy like. I checked the setting and it is in the right place.


It could be that the belt or belts are worn and when you put the brush against the resistance of the carpet the belt slips and causes it to be jumpy. If you haven't changed the belt lately I would try that. You can get the belts for this model here:
http://vacbelts.xps.convina.com/bissell-proheat-belt-combo-pack.htm

Oct 19, 2009 | Bissell 1697-7 Powersteamer Pro Deluxe...

2 Answers

Hover steam vac Model #F5897-900


When I use my Hover Steam Vac, it smells like rubber is burning. How do I fix this?

Jun 16, 2009 | Hoover SteamVac Carpet/Upholstery Deep...

1 Answer

Had a problem with the brushroll now its burning up the flat belt


When you put the flat belt on, is the print on the outside of the belt? Is the brush correctly positioned?

Dec 21, 2008 | Hoover U6630-900 WindTunnel Bagless...

1 Answer

Belt


Not sure yet, but I assume you mean the belt that drives the brush at the base.
If it is an older style cleaner, there would a be cover held on by a few screws.
This hold the brush in place so tkae note of how it is in place should it fall out of place.
Lift the belt off the motor spindle to replaceit.

Sep 14, 2008 | Morphy Richards Vacuums

2 Answers

Drive belt on upright bagless cleaner


if its like mine there is a rod that comes out f the moter usually on the upper left of the power head put t the belt around that and then slip the belt over the beater bar. Then replace the beater bar. You will have to pull a little to stretch the belt.

Jun 13, 2008 | Bosch Vacuums

1 Answer

The brushes will not turn. How do I open the unit to put the belt back on?


Hoover doesn't use belts on their steam cleaners. Either the shaft that is on top of the brush block broke off, or the turbine is bad. The turbine is what turns the brushs.

Jun 12, 2008 | Hoover F7220900 SteamVac V2 Upright Vacuum

1 Answer

How to replace a belt on a hoover tubopower 2000 vacuum


Hover does not list by model number. You will have to look on the back of your cleaner, on the same sticker as the model number, is a manufacturing code (MFG Code) or Serial Number. Go to Hover’s web page http://www.hoover.com/CustomerService/Manuals/Default.aspx and you will be able to download the correct manual free of charge.

Apr 05, 2008 | Vacuums

1 Answer

Changing belt on vacuum cleaner


If you can't see the motor shaft then you will have to take the top cover off. Some have a couple of scres to remove from the bottom. Then is a slot on each side, from the bottom put a flat blade screwdrive in the slot and push out and up to release the locking tabs. The knob may pop off so watch for that coming off. Put the belt on the brush roll, then feed the belt up thru the opening and stretch it to go over the motor shaft. Put back together.

Jan 20, 2008 | Vacuums

Not finding what you are looking for?
Vacuums Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18334 Answers

D. Floyd Kolb
D. Floyd Kolb

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...