Question about Hotpoint Aquarius WD640 Front Load Washer/Dryer

2 Answers

Aquarius Hotpoint WD440. 1400 Spin

Thanks very much for your assistance
When ever it get to the Rinse and Spin Stage,it stop and it does not do anything.
Please advise us what to do on this:Aquarius Hotpoint WD440. 1400 Spin
We look forward to getting your assistance
Thanks in advance!

Posted by on

  • markbrown440 Aug 05, 2008

    getting error code f-01. Machine fills with water then pumps back out again. Does anyone know what this code means?



    Mark

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hotpoint Wd440. I had the same problem, lights flashing and water not draining, First drain your water (syphoning works but tastes ****), if the machine drains then you know its not blocked. Then put the machine on M for about 5 mins, then put it on fast spin. This should do the trick, it worked for me anyway. Good luck.

Posted on Aug 10, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 172 Answers

The next step should be the pump out. If it is not pumping check your pump filter for obstructions. Check the drain hose and also your drain in the wall. If all are clear you may have a bad pump. You should have an error code coming up when the machine stops also, please let me know what it is. Thanks and I hope I can FixYa.
Mike

Posted on May 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, my Hotpoint Aquarius wma56 washes, but drum wont spin in rinse and wont spin...any advice?


you need to check/clear filter, its located within sump hose @ bottom of drum quite trickey clip to remove slide it to the side to assist then withdraw nylon filter and clear.

Jun 10, 2011 | Hotpoint Aquarius WMA56 Front Load Washer

2 Answers

Hotpoint wf540 stopping on a rinse and spin and


check pump/filter/outlet hose for blockages. if ok, check pressure switch (disc shaped item at top of machine with 4? wires and a tube) by blowing into it gently - should hear clicks, then blow into tube to pressure chamber - should be clear.

Oct 26, 2009 | Hotpoint Aquarius WF000 Front Load Washer

2 Answers

Hotpoint Aquarius Wf740 F-08 just before rinse and spin.


Hi my Hotpoint WF740 keeps flashin H20. Does anyone know why please?

Jan 15, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Started having a noisy rinse & spin cycle, then stopped.


Open the washer door and spin the drum by hand, if it feels rough or noisy and rumbling, then the main drum bearings have failed. There should be little or no noise when you spin drum
This is a major repair, and I would not recommend a D.I.Y solution.
Other possibility is there is something in the pump, but you would only hear this when the pump is working.

Plz rate my comments.
Thanks.

Jan 07, 2009 | Hotpoint Aquarius WF210 Front Load Washer

1 Answer

Wash machine stays on wash cycle and doesnt go to rinse or spin


If the water is not getting hot, this will probably stop the programme advancing .Check heater.
Plz rate solution to prob.

Dec 10, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

AQUARIUS HOTPOINT WD440


How many times does it flash.
it still sounds like you have an obstruction in something.

May 09, 2008 | Hotpoint Aquarius WD640 Front Load...

4 Answers

HOTPOINT AQUARIUS WF 250 ON/OFF LIGHTS FLASHING


The lights are set off by the balance sensors.And if your balance sensors are  stopping    it from spinning than you first have to make sure the washer is level.You  could have bad Shocks and a bad electronic control board,.                                    

May 05, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Does not spin and rinse properly


Sounds like motor is not coming up to spin speed. May be overheating, in which case you would need a new motor.

Feb 16, 2008 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Washer will not spin


normally i would suggest changing motor carbons for hotpoint washers, but my experience is that the WMA motor armature is weaker than the carbons, normally if there is no connection fault a replacement motor is the answer 9 times out of 10, not a job for the amature

Aug 28, 2007 | Hotpoint Aquarius WMA42 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

1,880 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...