Question about Konica Minolta magicolor 2430 DL Laser Printer

2 Answers

'DRUM CARTRIDGE END OF LIFE' MESSAGE

HAVE REPLACED THE DRUM AFTER MESSAGE 'DRUM CARTRIDGE END OF LIFE', BUT MESSAGE IS STILL THERE! WHEN I PRINT A TEST PAGE THE OUTPUT IS PERFECT.

THE NEW DRUM HAS BEEN TESTED IN ANOTHER PRINTER AND IS OK. ALSO THE ORIGINAL WORKS IN ANOTHER PRINTER.

Posted by on

  • JOHPAS May 13, 2008

    Hi

    I have now updated firmware (to2.13) but problem is still there. Have tried contacting Konika Minolta to request program to reset counter but have no response after several emails sent. Can you suggest where the program can bo found on the web?.

  • zukkur Jun 12, 2008

    I had the same issue with 2430dl, Updated the firmware, and then i got to know that the drum unit fuse was gone. yay! fixed ya!



    zuhaz

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

The back right of the drum has a small 20mm F80mA fuse that you need to replace to reset the drum counter.
(fuse blows to reset the drum life setting)

Posted on Nov 04, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 406 Answers

Try upgrading a firmware, Else contact service center to reset the drum counter ( get the program to reset or visit them with printer) . Else contact manufacturer.

Posted on May 09, 2008

  • Rafique Mannasaheb May 13, 2008

    The programmes are manufacturer secrets the y will provide on request.

    Now u may contact service center or. thouroghly clean with care and see. Else Authorised service centers may help you to solve this issue.

  • Rafique Mannasaheb May 17, 2008

    Now you may take the printer to authorised service center. Else if unable to reset at any attempt change mainboard at last.

    Regards

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i reset ricoh sp 1200s drum unit


why toner life end message keep on showing on sp 1200s prints.

Aug 04, 2012 | Ricoh Office Equipment & Supplies

2 Answers

Does the 'Drum Near End' message for MFC 8460N mean to indicate the toner cartridge needs replaced?


Same with our Brother 8640N, drum near end means toner is nearly to end but sometimes even you replace bew cartridge is appears this message. TONER LIFE END message need to replace cartridge.

Dec 17, 2010 | Brother MFC-8660DN All-In-One Laser...

2 Answers

I have the MCF 7340. I am getting a message - End of Drum Soon. So, I bought a new drum ($120) and installed it. Now it says Drum end. and won't print. Ive turned the machine on and off several times,...


If you open the front cover of your printer where you install the toner cartridge and press the "Clear/Back" button with it open, an option comes up on your LCD Display that says "Replace Drum?" press 1 to reset it. That should fix your problem!

Sep 11, 2010 | Brother MFC-7340 All-In-One Laser Printer

1 Answer

Toner light is on on Brother HL-2170 Laser Printer and the computer is not recognizing a print task. Can you help me fix this problem? Also, I just replaced toner a couple weeks ago.


Description of Problem 100000013553
I just replaced the toner cartridge and the Toner LED is still on, or the status monitor continues to display the message "Toner Life End". What can I do?

Description of Solution 200000017394
@font-face { font-family: Verdana;}@page Section1 {size: 8.5in 11.0in; margin: 1.0in 1.25in 1.0in 1.25in; }P.MsoNormal { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman"}LI.MsoNormal { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman"}DIV.MsoNormal { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman"}A:link { COLOR: blue; TEXT-DECORATION: underline}SPAN.MsoHyperlink { COLOR: blue; TEXT-DECORATION: underline}A:visited { COLOR: purple; TEXT-DECORATION: underline}SPAN.MsoHyperlinkFollowed { COLOR: purple; TEXT-DECORATION: underline}DIV.Section1 { page: Section1} If the Toner LED is still on, or the status monitor continues to display the message "Toner Life End" after installing a new toner cartridge, verify you are using a genuine Brother toner cartridge.

The yield of the TN starter toner cartridge is approx. 1,000 pages.
The yield of the TN330 toner cartridge is approx. 1,500 pages.
The yield of the TN360 toner cartridge is approx. 2,600 pages.
Approximate cartridge yield is declared in accordance with ISO/IEC 19752(Letter/A4).

Brother strongly recommends that customers use only genuine Brother drum units and/or toner cartridges. Each Brother laser printer is designed to work at pre-set temperatures that are matched exactly to each of our individual toner formulations. Each individual component is designed to work with the other to ensure quality and reliability. Using non-Brother supplies may affect the hardware performance, print quality and machine reliability. The Brother limited warranty does not apply to any problem that is caused by the use of third party drum units, toner cartridges or toner.

1. Verify you installed a NEW, out of the box, genuine Brother toner cartridge (TN360/TN330).

If a toner cartridge from another machine was installed (even if there?s still toner left in the used cartridge) or a starter toner cartridge (included with the purchase of a machine) was installed, the Toner LED will stay on and the message "Toner Life End" would continue to appear on the display.

2. Verify the toner cartridge is installed correctly by following the steps listed below:

a. Open the front cover by pulling the tabs on the left and right side of the printer towards you.

b. Lift the drum unit slightly and pull it out. Place the drum unit on a piece of disposable paper or cloth to avoid spilling and scattering the toner.

c. Remove the toner cartridge from the drum by holding down the lock lever (blue tab) on the left side of the drum unit and lift the toner out. Handle the toner cartridge carefully. If toner scatters on your hands or clothes, immediately wash it off with cold water.

d. Gently rock the toner cartridge from side to side five or six times to distribute the toner evenly inside the cartridge.

e. Place the toner cartridge into the drum (be sure it clicks into place).

f. Clean the primary corona wire inside the drum unit by gently sliding the blue tab on the top of the cartridge from right to left several times. Return the blue tab to the home position before reinstalling the drum unit assembly.

g. Reseat the drum unit into the printer pressing it in securely.

h. Close the front cover making sure it latches on both sides.

If the Toner LED is still on or the status monitor continues to display the message "Toner Life End" the printer will need service.

The printer has a one year limited exchange warranty. If the printer is in warranty, call Brother Customer Service at 1-877-Brother (1-877-276-8437) for warranty options.

If the printer is out of warranty, contact a Brother Authorized Service Center for repair by clicking on the link below:
http://www.brother-usa.com/service/default.aspx

Jul 21, 2010 | Brother HL-2170W Laser Printer

2 Answers

I am changing the ink cartridge i put the new one in and it keeps saying End of life and it has a new cartridge what do i do


Here is the solution that will reset the count and allow your fully functional toner cartridge (the one the printer tells you is empty) to continue to work.

Open the front cover.
Press options button.
Press the start button.
Press + or up arrow button 10 times.
Press set button.

You have to do this with a long pause or the system will reset and you will have to start over.

Good luck.

May 24, 2010 | Brother DCP-7020 All-In-One Laser Printer

1 Answer

Printer wants toner cartridge replaced, though not empty


unfortunately the drum within the cartridge has reached end of life so changing to a new drum cartridge would resolve this issue.

Mar 25, 2010 | Panasonic KX-FLB801 All-In-One Laser...

1 Answer

I have a brothers copier DCP 8060 and it has a message in the lcd window stating drum near end. What is this...is this is different than the toner cartridge?


The drum unit will wear out and need replacing. The toner cartridge clips into the Drum Unit.
If you print out the system setting report, it usually shows a bar graph with drum life indicated as a percentage.

Dec 08, 2009 | Brother Office Equipment & Supplies

1 Answer

Had toner life end message. Replaced toner and drum with oem,machine reset but now just making blank copies. Tried to print internal report that's blank too


To reset the sensor after installing a new toner cartridge follow these steps.
1. With unit powered On, open the front cover.
2. Press the "Options" key. Display will show "Replace Drum?"
3. Press "Start" key.
4. Press 1,0 .
5. Display will show "Accepted" for approximately 2 seconds. Then display will change to "Cover Open".
6. Close cover and see if Toner Life End error message has gone.
Please note that this must be done with a new cartridge so the unit will see that there is toner in the cartridge.

Aug 01, 2009 | Brother IntelliFax-2820 Laser Fax

3 Answers

Change of toner


I have a brother mfc 7840w

I first used the electrical tape trick and that worked for a while. Then got the toner low message again. I then tried the *00 trick, which works as follows:

1. lift lid and open front cover
2. press clear/back. "Replace Drum?" will appear on the screen.
3. Press "*00" it will then read accepted and the toner low error (End of Toner Life) should go away.
4. close it all up and your done.

Jun 08, 2008 | Brother MFC 7420 All-In-One Laser Printer

Not finding what you are looking for?
Konica Minolta magicolor 2430 DL Laser Printer Logo

3,781 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6161 Answers

Ben
Ben

Level 2 Expert

108 Answers

David Burkhart
David Burkhart

Level 2 Expert

210 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...