Question about Tasco 3-9x32 .22 Riflescope W/ Rings, Black Matte

1 Answer

I can get the elevation adjustment cap off. Is there some secret to elevation adjustment?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,702 Answers

If the scope is out the best way to set it up is to clamp the rifle in a jig or hold it hard done on a sand bag,,,firs off the first shot at the bull and see were the shot hit the card,,,now without moving the rifle turn the scope turrets till the cross is over the bullet hole from the last shot,,,now again aim at the bull and shoot again,,,the shot should hit the bull,,if not reajust the scope as before,,,

Posted on Aug 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My rifle is shooting about five inches high. Do I turn the elevation adjustment towards "up" or opposite of "up"?


If you have a scope, the adjustment is under the top cap, and you should turn the adjustment 'down'. If you have iron sights, you would adjust the rear sight in the same direction that you want to move the bullet on the target (also 'down'). The opposite is true if you are adjusting the front sight.

Dec 26, 2014 | Optics

1 Answer

Ironman 3900 treadmill will not work. code L 14


1) adjust the speed sensor, clean and tight the wires connector very well
2) lube the gear and shaft from elevation motor
3) adjust the potentiometer from elevation motor
4) measure the input voltage from elevation motor
5) Try to run the software calibration, for diagnose, troubleshooting
God bless you
6_12_2012_6_36_42_pm.gif6_12_2012_6_37_03_pm.gif

Jun 11, 2012 | Exercise & Fitness

2 Answers

Where can I get replacement caps for the elevation adjustments.


the only way to find cheap caps it try a fuw gun shops to see it they have any old scope that dont work and buy the caps that will fit your scope most gun shops keep old broken scopes just for that?

Nov 27, 2010 | Burris 3-9x50mm Fullfield II Rifle Scope...

1 Answer

Have no idea how to set up the sight on my air gun


I don't have this particular model. Chances are, those are not "knobs" but caps. Remove the caps as you would remove the caps from a pill bottle. Underneath, you should find the adjustment dials for windage and elevation,

You can download a generic Simmons scope manual here:

http://www.simmonsoptics.com/downloads/manuals/archive/HSI_Simmons%20Generic%20Scope%20Adjusting%20Instructions.pdf

Apr 04, 2010 | Simmons 511070 4x32 22 MAG Riflescope -...

1 Answer

Simmons 8x32-44ao rifle scope


Is that the "Prairie Master"? I think Simmons is pretty uniform in that range of scopes--elevation adjustment should be the top dial and windage is on the side. The zoom locking ring should be in front of the eyepiece, with the zoom ring just forward of that.

You can download a generic Simmons scope manual from the Simmons site at this link: http://www.simmonsoptics.com/downloads/manuals/archive/HSI_Simmons%20Generic%20Scope%20Adjusting%20Instructions.pdf

Mar 31, 2010 | Simmons 510513 3-9x40 Blazer Riflescope -...

1 Answer

Hi, I have lost the elevation adjustment cap to my hammers 3-9x42GDT scope. Where may I find a replacement? Thanks, Henry


Henry, you need to have the name, make and model of your scope, make contact with the manufacture and, purchase a replacement part

Dec 04, 2009 | Hammers Optics

2 Answers

Tasco scope issues with elevation adjustments


Take the lens caps ff.Then run a new Leupold under it..

Jan 16, 2009 | Zeiss CONQUEST 3-9X40 MATTE Z PLEX

1 Answer

Lost caps


I'm not sure how this got posted in the car audio section...

 

If the scope was manufactured by a well established company, you should be able to get a new cap from them.

 

If you cannot locate the manufacturer, you can move the other cap to the windage adjustment to set the windage. Then when you're finished, move the cap back to the elevation adjustment.

 

Even if you use it for a shooting discipline that requires constant adjustment, it's unlikely that you'll need to use the windage adjustment for anything other than setting the zero.

Oct 16, 2007 | Hifonics Titan TX 8805 Multi-Channel Amp...

Not finding what you are looking for?
Tasco 3-9x32 .22 Riflescope W/ Rings, Black Matte Logo

275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tasco Optics Experts

Joe Lalumia aka...
Joe Lalumia aka...

Level 3 Expert

3186 Answers

Mark Campeau

Level 1 Expert

44 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Tasco Optic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...