Question about Wasp WPL305 Thermal Label Printer

1 Answer

How to replace printhead wasp 305 - Wasp WPL305 Thermal Label Printer

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Remove the ribbon. On each side of the head is a small yellow tab. Push one side in then drop that side of the head and pull the other side out. Disconnect the connector on the back.

Posted on Sep 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you treat a wasp sting?


Vinegar wash for wasps, alkali sting.

Bicarbonate of soda for bees, acidic sting.

Dec 30, 2016 | Wasp Computers & Internet

1 Answer

Line across docs where the ink has missed


clean your printhead. it has a partial plug. you can run some cleaning cycles or make a cleaner cartridge. this involves drilling the cartridge and taking a syringe and putting about a full syringe of windex into it and sealing it with hot wax and then putting it into the printer and running cleaning cycles, or taking a small plastic hose on a syringe and putting a pool of windex on the ink pads where the printhead comes to rest and turning the printer off and let it sit for a few hours. it will try to suck the windex out into the waste ink pads so you have to get it there just as it parks. it will let the printhead sit in the windex and wick up into it to unclog it.

May 23, 2015 | Epson Expression XP-305 Inkjet...

1 Answer

Epson xp 305 help


It's quite likely that at some point in time you will have attempted to print in black only to receive an error message that you cannot print until a colour cartridge is replaced.
"If ink is not in the tubes from the head to the cartridge, air will be sucked in and therefore cause damage to the print head. This is because the nozzles are in the print head and not in the cartridge. "
What Epson are basically saying is... if this safeguard was not in place, and you sent a print request for black when a colour cartridge was empty, there is a risk of air being pulled into the printhead. This air will ruin the vacuum effect needed for the printhead to pull ink in, meaning your printhead would be at risk of never printing again.
Additionally, if any air is allowed go get into the aformentioned tubes from the head to the cartridge, any remaining ink will coagulate. Just in case you're not a scientist - coagulation in a tube/cartridge is bad, and will lead to you not being able to print again with that cartridge, or to a blocked nozzle/printhead which will require a significant amount of cleaning cycles to budge.

Aug 08, 2014 | Epson Expression XP-305 Inkjet...

2 Answers

Wasp wpl 305e


The WPL 305 E is Ink side IN or OUT? And the core is?

Dec 05, 2013 | Wasp WPL305 Printer

1 Answer

How to replace battery for wasp technologies wws-800 scanner


There is a slide on the bottom of the unit, move it to unlock position and slide battery out. Reverse procedure for installing the new one.

Apr 30, 2010 | Wasp WWS800 Handheld

1 Answer

Broken part of soft top of Jaguar XK8 convertible 1999


hı thıs ıs cıhan pekın ıhave xk8 1997 ı m lookıng complate soft top for my car because mıne was broke ın that case ı can sent your neeeded parts ı u wısh also could you help me for used complate soft top (blue)my best regarts

Oct 25, 2008 | 2007 Jaguar XK8

1 Answer

Label gap


probably your label not ok,or you have some label stick on the sensor in the printer.open the printer and check

Feb 07, 2008 | Wasp WPL606 Thermal Label Printer

Not finding what you are looking for?
Wasp WPL305 Thermal Label Printer Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wasp Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Wasp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...