Question about Bushnell Cameras

1 Answer

Installed batteries and sd card. Pushed power button nothing happens except batteries heat up... can you help?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

There is a problem in the supply unit of your cam, you can get it repaired by taking it to a camera repair shop.

Posted on Aug 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does nothing happen when power button pushed?


The Dyson cords are known to go bad, test the cord and see if there is voltage. If this is too mechanical for you, please take the vacuum to your nearest vacuum repair shop

Mar 21, 2016 | Dyson DC44 Animal Handheld Vacuum Cleaner

1 Answer

Model# 5844 digital display works, heat element works, will not start motor when switch is pushed


Is the lid closed? Many bread makers have a safety switch to keep the motor off if the lid is open. The blades are quite strong and could break your fingers.

Nov 25, 2015 | Kitchen Appliances - Others

1 Answer

I forgot my numbered pass code on my android tablet and put it in safe mode but it won't do anything. I also have a pinhole on the back and pushed it and nothing happened.


Turn the tablet off, and remove the SD memory card if there is one. Hold down the power button and both volume buttons until your device vibrates.

Jan 04, 2014 | Tablets & eReaders

1 Answer

Not quite sure what happened someone pushed the red sync button on the console now my controller wont work you know the finger that is suppose to display


You have to re-synch the remote with the system now.

Standard Mode Synchronization
Note: Make sure you have placed batteries in the Wii Remote (how to).
  1. Press the Power button on the Wii console to turn it on.
  2. Open the SD Card Slot cover on the front of the Wii console. Remove the battery cover on the back of the Wii Remote you wish to sync up.
  3. Press and release the SYNC button just below the batteries on the Wii Remote; the Player LED will blink. Quickly press and release the SYNC button on the inside of the SD Card compartment on the console.
  4. When the Player LED blinking stops, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

May 10, 2011 | Nintendo Wii Console

1 Answer

I was removing the video card to tighten a nut. I unplugged the power cord and pushed in the power button to drain excess power, notice the solid green light went to flashing. I then removed video card to...


Open it up again. Take the video card out. Take the Ram out. Unplug the hard drive. Unplug the other drives. Unplug the network card(s). And unplug anything else that is tied to the motherboard. Now plug it all back in snugly.Finally,turn it on. It should be fixed.

Nov 23, 2010 | HP Pavilion a1330n (EL466AA) PC Desktop

1 Answer

PSU hangs the system: can't turn on; turns of in 30 min


either the power supply needs replaced or there is a short on the board...

pull the mb and guts of the system out of the chassis

connect the power supply with one cpu and one stick of memory for testing.. no add-in cards installed

then test the power capabilities..

if the system works out of the chassis.. ( alot of work to do ...understood )then there is short to the chassis of the from the motherboard

i really think the power supply is the issue though

Sep 29, 2009 | Computers & Internet

1 Answer

Coolpix L1 that won't take a picture after getting wet


try dismantling you will find a gooey substance in a microchip. try removing it.i hope it works

Sep 12, 2009 | Cameras

3 Answers

Oven won't heat.


EUREKA! I found the reset button and my oven is heating as we speak. Ok, open the oven door. there is a thin panel with vents right at the door latch. Unscrew the (6) screws and pull off the panel. There is a red button on the left back behind the wiring. GOOD LUCK!

Dec 08, 2008 | Dacor ECS130 Epicure Electric Single Oven

1 Answer

Plz help


remove the SD Card and the batteries. Wait for half an hour and then insert two new batteries. Do not put the SD card in as yet. (Waiting for half an hour or more allows the camera to reset itself).

Now try switching on and good luck.

Dec 27, 2007 | Kodak EasyShare C653 Digital Camera

Not finding what you are looking for?
Cameras Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bushnell Cameras Experts

kakima

Level 3 Expert

102366 Answers

Johnny Massengill
Johnny Massengill

Level 2 Expert

345 Answers

Brad Brown

Level 3 Expert

15441 Answers

Are you a Bushnell Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...