Question about Belkin (F5D5231-4) Router

1 Answer

Adding a user

I want to add another computer on to my security list, but i don't know how to get to the internet page that shows the list. help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 230 Answers

Go to dos prompt, type "ipconfig"
type the IP of the gateway into your IE.
You might need ID/Pass into your router.
then click on LAN tab. Add IP/MAC to this list and save.

Posted on May 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I just got an ipad and would like to access the internet from it. The ipad is asking for my security password and I have misplaced it. Can you email me the security password please? Thank you


The security key is listed in your router. To find it you have to log onto the setup page of your router,there you will find it under Wireless tab, then security.

Depending on your router you need to open it's setup page in your Internet brwoser:
Linksys 192.168.1.1
Belkin: 192.168.2.1
D-Link: 192.168.0.1
Netgear: 192.168.1.1

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe

Jan 29, 2011 | Routers

1 Answer

Can't get to wireless setup page.Set network name &security


you can use default ip 192.168.1.1 go to this page from internet explorer, then they ask you for user name and password just you type ADMIN/ADMIN then enter.. after you can change your any setting.. hope to solve your problem...

Apr 29, 2010 | NetGear WNR1000 Router

1 Answer

How do I install it?


First connect your router to computer with ethernet cable.
Then you can access it with following default link.
http://192.168.1.1
or
http://192.168.0.1
Type user as "admin" and password as "admin" or blank or "password".
Then you can see configuration page of router.
Set WAN settings as your internet service provider.
If you internet need user name and password for connect then you need to configure router in PPPoe mode.
Enable DHCP if you want ip address from router.
Click on wireless and enable wireless .
Enable WEP security if you want secure wi fi.Then add WEP code then save settings and router.
Then disconnect router from computer and connect internet service provider cable into it.
Then you can use it wireless.
Let me know if you need further assistance.
Thanksd for using FixYa.

Jan 06, 2010 | NetGear WGR614 Wireless Router

2 Answers

Network wont show up on any Wireless Network List


Reset your router to factory defaults.
For that press RESET button for 10 seconds it is in back panel of router.
hen connect your router to computer with ethernet cable.
Then you can access it with following link.
http://192.168.1.1
or
http://192.168.0.1
type user as "admin" and password as "admin" or blank or "password"
Then you can see configuration page of router.
Set WAN settings as your internet service provider settings.
Enable DHCP .
Click on wireless and enable wi fi.
If you want secure router then enable WEP security then add new code it is your password key for connect wi fi.

Then save settings and restart router.

Let me know if you need further assistance.
Thanks.

Nov 10, 2009 | NetGear WGR614 Wireless Router

1 Answer

Need to know/find 'User Name'and 'Password'also 'Service name'


connect your router to computer with ethernet cable.
Then you can access it with following link.
for belkin routers http://192.168.15.1type user as "admin" and password as "admin" or blank or "password"
Then you can see configuration page of router.
Set WAN settings as your internet service provider settings.
.
If you are not able to see router settings with above link then you need to reset router for that press RESET button for 10 seconds it is in back side of router.
If you want secure router then enable WEP security then add new code it is your password key for connect wi fi.
Let me know if you need further assistance.
Thanks.

Nov 09, 2009 | Belkin F5D7230-4 Kit (F5D7230V4SNPDQ)

1 Answer

Using the router


First connect your router to computer then access your router as following link.
http://192.168.1.1
or
http://192.168.0.1
type user as "admin" and password as "admin" or blank or "password"
Then you can see configuration page .
Then set WAN settings as your internet service provider settings.
Enable DHCP.
Go to wireless enable wireless.
SEt wep security if you want secure wi fi.Add WEP code it is your password to connect internet so only who know the password are connect to your wi fi .
Then save settings and restart router.
Let me know if you need more assistance.
Thanks.

Oct 04, 2009 | Actiontec GT704WG Wireless Router...

1 Answer

I don't know how to port forward my comtrend adsl+


A. Determining the IP Address and MAC Address of a Computer:

Note: Please use the computer for which the Ports are to be opened:

For Windows 2000/XP users:

1. Please click on Start and select Run.
2. Type in cmd and click on OK.
3. In the Command Prompt, please type ipconfig/all then press Enter or Return key.
4. Please make sure that the Ethernet adapter has an IP Address that is the same range as the router (e.g. 192.168.1.2 for the computer and 192.168.1.1 for the router).
5. Please note down the IP address and Physical address.

B. Reserving an IP Address:

1. Please open any web browser like Internet Explorer or Netscape Navigator.
2. Connect to the router by typing http://192.168.1.1 in the address field and click Enter or Return key.
3. A window will prompt for a user name and password. The default username is "admin" and the default password is "admin".

4. When the setup page opens, click on LAN IP Setup under Advanced tab.
5. Click on Add under Address Reservation.
6. Under Address Reservation window, please select the radio button of the computer you wish to add from the Address Reservation Table.
7. If the computer you want is not on the list, please click on the Refresh button to update the table.
8. If the computer is still not on the Address Reservation Table, please type in the IP Address, MAC Address (Physical Address), and Device Name of the computer you wish to add.
9. Click the Add button when done.

C. Opening Pre-Defined Ports for Internet Services:

1. Click on the option with the name Port Forwarding/Port Triggering under the Advanced menu.
2. Please select the service type Port Forwarding. The router pre-defined services are listed there.
3. From the Service Name pull down list, select the service that needs to be hosted.
4. Enter the IP address of the computer in the Server IP Address box.
5. Click the Add or Apply button.
6. Repeat all steps to open more ports.

Note: If the name of the Internet service does not appear in the drop down list, you may manually open the ports for that Internet service. Please follow the steps below:

D. Opening Ports for Games, Applications or Custom Ports:

1. Click on Add Custom Service button.
2. Type the service name in the Service Name box and the lower range numbers in the Starting Port box.
3. If the application uses only a single port; type in the same port number in the Ending Port box.
4. If the application uses a range of ports; type in the higher range numbers in the Ending Port box.
5. Type the IP address of the computer in the Server IP Address box. Click Apply button.
6. It will then refresh to the Port Forwarding page, and will show the list of all ports opened in tabulation.
7. Repeat all steps to add more ports for more services.

E. To Edit or Delete a Service Entry:

1. Click on the Radio Button that needs to be Edited /Deleted, under the Port Forwarding page.
2. Modify the information from the Service Name, Starting Port, Ending Port, and the Server IP Address, and then click the Apply button.

Sep 25, 2009 | Linksys WRT55AG Router

1 Answer

How to i get to the wan in the advanced section of the router?


A. Determining the IP Address and MAC Address of a Computer:

Note: Please use the computer for which the Ports are to be opened:

For Windows 2000/XP users:

1. Please click on Start and select Run.
2. Type in cmd and click on OK.
3. In the Command Prompt, please type ipconfig/all then press Enter or Return key.
4. Please make sure that the Ethernet adapter has an IP Address that is the same range as the router (e.g. 192.168.1.2 for the computer and 192.168.1.1 for the router).
5. Please note down the IP address and Physical address.

B. Reserving an IP Address:

1. Please open any web browser like Internet Explorer or Netscape Navigator.
2. Connect to the router by typing http://routerlogin.com/basicsetting.htm or http://192.168.1.1 in the address field and click Enter or Return key.
3. A window will prompt for a user name and password. The default username is "admin" and the default password is "password".

Note: If it does not take password as the password, you might have changed it when you have run the NETGEAR Setup CD so please try other passwords. If you cannot remember the password, you need to reset the router and run the Setup CD to reconfigure it.

4. When the setup page opens, click on LAN IP Setup under Advanced tab.
5. Click on Add under Address Reservation.
6. Under Address Reservation window, please select the radio button of the computer you wish to add from the Address Reservation Table.
7. If the computer you want is not on the list, please click on the Refresh button to update the table.
8. If the computer is still not on the Address Reservation Table, please type in the IP Address, MAC Address (Physical Address), and Device Name of the computer you wish to add.
9. Click the Add button when done.

C. Opening Pre-Defined Ports for Internet Services:

1. Click on the option with the name Port Forwarding/Port Triggering under the Advanced menu.
2. Please select the service type Port Forwarding. The router pre-defined services are listed there.
3. From the Service Name pull down list, select the service that needs to be hosted.
4. Enter the IP address of the computer in the Server IP Address box.
5. Click the Add or Apply button.
6. Repeat all steps to open more ports.

Note: If the name of the Internet service does not appear in the drop down list, you may manually open the ports for that Internet service. Please follow the steps below:

D. Opening Ports for Games, Applications or Custom Ports:

1. Click on Add Custom Service button.
2. Type the service name in the Service Name box and the lower range numbers in the Starting Port box.
3. If the application uses only a single port; type in the same port number in the Ending Port box.
4. If the application uses a range of ports; type in the higher range numbers in the Ending Port box.
5. Type the IP address of the computer in the Server IP Address box. Click Apply button.
6. It will then refresh to the Port Forwarding page, and will show the list of all ports opened in tabulation.
7. Repeat all steps to add more ports for more services.

E. To Edit or Delete a Service Entry:

1. Click on the Radio Button that needs to be Edited /Deleted, under the Port Forwarding page.
2. Modify the information from the Service Name, Starting Port, Ending Port, and the Server IP Address, and then click the Apply button.

Jun 10, 2009 | NetGear RangeMax WPN824 Router

2 Answers

Adding a device


Is your network a secured network?

Oct 08, 2008 | Westell Wirespeed VersaLink...

Not finding what you are looking for?
Belkin (F5D5231-4) Router Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Belkin Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

steve morris
steve morris

Level 3 Expert

1673 Answers

Christopher Thrash

Level 3 Expert

425 Answers

Are you a Belkin Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...