Question about Hotpoint Aquarius WMA56 Front Load Washer

2 Answers

Hotpoint aquaris wml 560, 1) all lights flashing nothing working, turned power off and on and it started to work ok. 2) all lights flashing (start light orange not green) no programs working, tried on and off still nothing. tried holding on/off button in with start button nothing. lights not flashing now just the set progam light and door locked light on but nothing happening.

Posted by on

  • steve_hodgso Aug 30, 2010

    Thank you.
    Is changing the board something that i could do myself?

×

2 Answers

Donald DCruz
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    Superstar:

    An expert that got 20 achievements.
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.

  • Hotpoint Master
  • 17,129 Answers

Possible that the inlet valve is not working or the ccontrol unit is faulty.
Please switch off and when switched on check for the voltage to the inlet valve, if water flows, if not the control panel is faulty.
If voltage is present and valve does not work then the valve is faulty.
Also check the DOOR switch( a safety switch) because if the switch is not working the control panel will not allow the control panel to proceed to switch on motor.
Also check and tighten all the connectors to the control panel.

Posted on Aug 31, 2010

Terence Fourie
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 909 Answers

Hate to tell you this, but the board must be replaced. Once the lights start flashing it is an indication that the program is corrupt. If you dont have anyone who can reprogram the micom, then install a new board. Quote the model and serial no. to the supplier to get the correct board.

Posted on Aug 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

6ya.com

Download 6ya

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint aquaris wf220 door closes and all lights working but machine won't start ?
CHECK UR DOOR SWITCH

Aug 27, 2014 | Hotpoint Aquarius WF220 Front Load Washer

1 Answer

How do i remove the drum from a Hotpoint Aquarius WML 560 P
Hi,
There is not much you can do to remove the drum of your WML 560 P Washing Machine...you can remove the bearings and door but you can't remove the drum personally. You'll have to take it in for service but here is a manual for you which you can read through to see if there is anything about removing the drum. Click on the link below to be directed to your Hotpoint Aquarius WML 560 P User Manual homepage...
Hotpoint WML 560 Instructions For Use Manual

Aug 26, 2014 | Washing Machines

1 Answer

I have a hotpoint wml 540 p/g/a/k and the cycle will not start. The machine allows me to turn it all on etc but when i press the start button the door does not click and the red key symbol flashes. There...
I have had this problem with mine. Turn off the machine at the mains (might be awkward if the switch is behind the machine!) wait a couple of mins and then turn back on again. It should now work!

Nov 16, 2010 | Hotpoint Washing Machines

2 Answers

Lights flashing
temp solution, switch on and off at wall socket with on/off switch in and out, untill only on/off switch is lit, then use wall switch for power on off. worked for me.

Jul 13, 2010 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Door light no working so machine will not start
check power is getting to machine with suitable electrical screw driver.to do this remove top from machine and check live wire just inside rear of machine. fault could be door lock if you have power in machine

Feb 05, 2010 | Hotpoint Aquarius WMA42 Front Load Washer

2 Answers

Spin not working properly, sounds ok but clothes are too wet once complete and the independent spin cycle leaves clothes soaking!!!
Sounds like a small blockage in the outlet pipes, possibly just in the filter but check all outlet pipes. Just done one the other day and it was a clothes button that had passed out of the machine through the pump to the outlet pipe but had turned sideways inside the outlet pipe.

Jan 25, 2010 | Hotpoint Aquarius WMA56 Front Load Washer

3 Answers

Error code F-05 for hotpoint aquarious washing machine
your pump/filter/outlet hose is blocked. clean it all out with the power off.

Oct 30, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Hello, My Hot Point Washer/Dryer is AQUARIES WD420 Model. I am on a "Wash cycle G50", but the light of the "on/off" switch is flashing and the lights of the "Dry High Heat" as well as "Reduce Creases" are...
Problem solved. Thank you.

Oct 10, 2009 | Hotpoint Washing Machines

2 Answers

HOTPOINT aquarious extra
try putting the drain lower worked on our WF 541

Dec 15, 2007 | Hotpoint Aquarius WF000 Front Load Washer

4 Answers

Hotpoint aquarious wf620
funny my machine does the same, i have had 2 answers one says to hold both the on off button and start button till it comes out of test mode? well something like that, (didn't work) and another tells me its just the board thats faulty, I do believe myself this can be reset by the right test equipment from Hotpoint (Hotpoint not helpful and i have a Hotpoint engineer as a neighbour), its also most embarrassing as i am a recently retired appliance engineer myself of 20 years, i have also been told its a conspiracy to get an engineer to call out to reset it and charge for doing so (being a computer control machine (not sure myself, these things don't happen - do they) Ps if you get told a cure and it works tell me please

Sep 18, 2007 | Hotpoint Aquarius WD63 Front Load...

Not finding what you are looking for?

View Most Popular

Aquarius WMA56 Front Load Washer

  • Washing Machines

Related Question

Hotpoint aquaris wf220 door closes and all lights working but machine won't start ?

  • Hotpoint Aquarius WF220 Front Load Washer

Open Questions:

0 Answers

i have a thin wire trapped in my drum making a terrible noise is there anyway i can get it out.

Jun 01, 2015 | Hotpoint Aquarius WMA56 Front Load Washer

0 Answers

how do you remove the black hose at the back of the machine where the filter is located? need to remove and clean the filter from the rear of the machine

Sep 12, 2014 | Hotpoint Aquarius WMA56 Front Load Washer

0 Answers

drum wont turn

May 27, 2014 | Hotpoint Aquarius WMA56 Front Load Washer

0 Answers

Why are Lights flashing in sequence hot point Not completing wash cycle lights chasing drum not going round

May 14, 2014 | Hotpoint Aquarius WMA56 Front Load Washer

See all Hotpoint Aquarius WMA56 Front Load Washer Questions

Hotpoint Aquarius WMA56 Front Load Washer Logo

Related Topics:

1,331 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Hotpoint Ultima WF860 Front...

Hotpoint Aquarius WD640 Front...

Hotpoint Aquarius WD63 Front...

Hotpoint Aquarius WMA42 Front...

Hotpoint Aquarius WD63 Front...

Top Hotpoint Washing Machines Experts

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

freddyfox

Level 2 Expert

236 Answers

ptpumpman

Level 3 Expert

407 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...