Question about Cameras

1 Answer

My yashica EZ F 527 always display card protected everytime i take pictures. How can i dissable it so that i can use the camera?

Posted by on

  • Anonymous Mar 30, 2014

    AKFKFKO OEFOEKOFKEOFOEKF EOFMOE FKOEMFEO FOEF M

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,831 Answers

Hello

OK, if the memory card itself is locked, you might sometimes get this error code. All you need to do is to take out the memory card and switch the lever on the left side to the unlock.

My yashica EZ F 527 - 6c99e31.jpg

If the error is still displayed after you did the above, you might want to try the card in another camera.

If the card works in another camera . the problem is with your card reader in your camera.

If you open you sd slot and look inside with a sharp light , you should be able to see on the left side of the slot there is a little copper or spring steel lever switch. This switch work as follows:

1. When no card is inserted / no write protection , the switch is open and thus the protection is off.
2. When locked card is inserted , the tab is depressed and tells the camera that the card is lock.

Contrary to popular belief ,the little tab on the sd card is not an electronic switch and does not physically influence the card operation itself. If you put a locked card into a camera without a sd lock switch , you would still be able to use the card normally.

It is incredible difficult to fix this switch because of space limitations in the sd card. Look into the sd slot and if you can see the switch , use a needle to pull the little tab down toward the base of the camera by about 2mm or until it works being careful not to bend it.

If this does not resolve your problem , there might be a short in the switch circuit and the camera will need to be disassembled to resolve this error. This should cost no more than $50.

Please feel free to contact me if you need further information

Kind regards
Andrea

Posted on Aug 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to unlock memory card of yashica ez f5 zoom?


SD cards have a slide switch along one edge. The position farthest from the metal contacts locks the card, protecting it from writes. The position nearest the contacts unlocks the card.

May 19, 2014 | Cameras

1 Answer

Hi i can't used my yashica EZ digital 5032 everytime i put sd card tells it error or no card


Your SD card may have failed. Have you tried a different SD card in your camera? If you have and it still isn't working, it may be the camera.

Apr 17, 2014 | Cameras

2 Answers

My yashica ez f5 zoom is giving a problem that is shown on the screen protected card ; what can i do to slove the problem.


Look at your memory card. SD cards have a slide switch along one edge. The position farthest from the metal contacts locks the card, protecting it from writes. The position nearest the contacts unlocks the card.

Nov 08, 2012 | Cameras

2 Answers

Plzz give me the Address Of Yashica Service Centre at Location-India State-gujarat City - Surat


Sorry, there isn't one. Contax/Yashica no longer exists as a company and there is no ongoing servicing/spare part support.

If you have a fault then you must use any generic camera repair shop of your choice, but some faults will not be repairable if spare parts are required unless the shop has scrap donor spares. Given that Contax/Yashica were never mass sellers, finding spares donors is also difficult.

Sorry that I cannot provide the answer you really want on this occasion, but I hope that my reply has been of some assistance to you.

Aug 12, 2010 | Kyocera Yashica T4 35mm Point and Shoot...

2 Answers

Ac adapter for yashica ez digital f8035


I am using camera yashica digital model ez f8035 now when i take picture or made video this is show in camera but not shown when i attahed it with computer and memory card show blank.\r\nplz tell me the soulation immediate because this is very important i want share some thing with my family.

May 30, 2010 | Cameras

2 Answers

Yashica ez digital 6032- 6 mp camera.. i got one sparingly used yashica camera... with above spec... which shows trouble when taking stil pictures outdoors... indoor pictures and video indoors n outdoors...


i am using yashica ez digital 6032 camera but while using SD card of 4GB memory, it is not working. it is asking to format. Pl. help me regarding this problem. Shall i format the camera?

Apr 27, 2010 | Cameras

2 Answers

Yashica EZ Digital 5032 5.0 MEGA battery cover open


Hi,
You can contact Latif Precision Works, 24, Chowringhee Road, Calcutta 700087, India. Phone 91 33 2249 2265, web latifprecisionworks.com

Apr 19, 2010 | Cameras

Not finding what you are looking for?
Cameras Logo

Related Topics:

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cameras Experts

kakima

Level 3 Expert

102366 Answers

Steve

Level 3 Expert

3287 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...