Question about Kenmore 72055 Air Conditioner

1 Answer

Reset button does this model have a reset button if so where would it be located

Posted by on

  • Anonymous Jul 08, 2008

    air conditioner keeps cutting off

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

It should be at the plug. should be a test and a reset, like a GFI outlet. if not there is none, let it cool down say a prayer or 2 and plug it back in.

Posted on May 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to turn off blinking light for air filter service


You can try to hold down 2 buttons at a time for about 3 seconds. Obviously it does not have a "reset filter" button. If it does and that didn't reset it then try to hold the reset filter button along with another button. Its head to say which one(s) to hold down. Also, the configuration menu, if you know how to access it, has an option that allows you to remove that feature most of the time depending on your model. You can also try to figure out the model of t-stat that you have. Most of them have a model number on it but always behind the face or on the back of it somewhere. If you had the maker and model # you could get an answer from the maker if they have a customer support helpline or locate a PDF for the owners/installation manual.

Jun 04, 2015 | Filter Air Conditioners

1 Answer

Rheem reset button location


Look on the cicuit board with all the electronic parts you should find a little red button

Dec 06, 2013 | Goodman CKL36AR36 Air Conditioner

1 Answer

Lg airconditioner model LP153HD3A has a fault on it reading ch 09 and can't figure out how to fix it please help


Unplug the unit wait 30 seconds Plug the unit it back in and hit the large reset button located on the male end of the plug head.

Aug 06, 2011 | Air Conditioners

1 Answer

The readout on the thermostat says "bae lo". I pulled the face of the thermostat off the wall and it reset and I was able to push "run program", but the furnace did not come on.


welcome to Fixya !

here are some steps that you may follow. open the remote and remove batterys or cell of your model for six seconds (i dont know .cause you didnt mensioned the Model.) then place them back.
start the A/C again , see if it works if it doesn't then follow the lower step. and if it helps ignore the rest of paragraph

now open the Air conditioning vent and find the Sensor of the remote near the sensor there shall be a button very small one , maybe its located in a hole. check and observe keenly .
just push that button for once .it will reset the AC. to default

if it doesn't help then comment with a model no
best Regards

Apr 12, 2011 | Air Conditioners

1 Answer

Where is reset button located on whirlpool split ac front panel? (Mastermind series chrome). Though I cleaned my filter the "filter" light is still glowing and hence i need to reset it but I am not finding...


Look real hard on the remote. There is a mini "use a ballpoint pen" push to reset filter button on the remote.

Electronic control panel: (not all models)
Hold the mode button and the Temp Up arrow depressed for about 5 seconds. It should display the temp and the FL should disappear.

Thanks for choosing FixYa.

Kelly

Sep 05, 2010 | Whirlpool ACC108PS Air Conditioner

1 Answer

Where is reset button located on whirlpool split ac front panel? (Mastermind series chrome). Though I cleaned my filter the "filter" light is still glowing and hence i need to reset it but I am not finding...


Look at your remote carefully. There is a bal pen type push to reset filter button on the remote. Depress the rest button and it should reset. Also on the contol panel you can also reset it by depressing the mode and the UP temp arrow buttons for 5 seconds.


Thanks for choosing FixYa.

Kelly

Aug 09, 2010 | Whirlpool ACC108PS Air Conditioner

1 Answer

Power failure unit went off of a rudd split unit


If he reset it on the outdoor unit, this could be a high
pressure switch located where the compressor is, which is attached to the refrigerant line.

Make sure your indoor unit operates by putting the fan to manual, if it operates your problem is not there.
Make sure your breakers have not tripped which should be located in an electrical panel in the house

Jun 28, 2010 | Ruud UAKA030 Air Conditioner

2 Answers

Replace remote control unit model ar-fb2


If your remote control have display but cannot transmit signal to the unit. Confirm first if the remote is really the problem, using your camera or cellphone camera as your eyes point the remote transmitter to your camera and "on" the remote. You should see light emits in your remote control, if no emitted light then the remote control is defective. But if there is a light the defect is in the unit receiver.

Check also if there is a reset or rst button in your remote control and reset it and try.

Check also if there are error codes in the unit, reset the unit by disconnecting the power supply in the unit for 10 sec. and "on" again and try.

The unit can be operate without remote control, use the manual button located in the unit.

If the remote control have no display replacement of remote is recommended.

Jan 15, 2009 | Air Conditioners

Not finding what you are looking for?
Kenmore 72055 Air Conditioner Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Air Conditioners Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

John Tripp
John Tripp

Level 3 Expert

4636 Answers

Bill Long

Level 3 Expert

577 Answers

Are you a Kenmore Air Conditioner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...