Question about Cyber Acoustics CA-3550 Computer Speakers

1 Answer

Only one speaker works

I have everything plugged in correctly and for some reason the base speaker went out and same with the right one. i dont know what happened. they used to work perfectly. any help is appreciated thanks

Posted by on

  • buzzkut May 14, 2008

    nah it didnt work everything was still defaulted anyways...im guessing the wire is just bad or something. thanks tho

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 46 Answers

If you have plugged correctly without any losse contact it should work if not o think your speaker configration is not correctly set go to the control panel->sounds and audio devices->device volume->advanced there u set that balance slider to middle of all volume control,wave,sw synth,line in etc.. then go to speaker settings in the same window of sounds and audio drivers there in speaker settings click on advanced you get another window in that drop down box specify your speaker configration wether is desktop speakers laptop mono speakers or stereo headphones etc specify the right one you have then ok after this in speaker settings click on speaker volume and keep left and right speakers to maximum then apply ok this will work check it out if stil not worked tell me what ws the result ill solve that for u

Posted on May 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Speakers not working


Check the easy stuff first: make sure the volume is at a reasonable level and play sounds from multiple sources like pandora, youtube, a local mp3 etc to make sure issue is consistent.

Next make sure the one or more wires are plugged into the correct ports. Or at the very least the green wire is plugged into the green plug on the computer (unless they're USB speakers?).

You could always look at the sound settings of Windows and see (if your sound card has multiple plugs) if the plugs and assigned different functions (base speaker versus microphone/headphone etc.). Hope this helps!

Jun 03, 2010 | Logitech X-530 Computer Speakers

2 Answers

JBL Creature Speakers have very low volume


use another device like your i pod to make your jbl sounds louder and then plugged it to your pc without turning it off. after plugging try to test it if works.

Apr 02, 2009 | JBL CREATURE II Computer Speakers

1 Answer

No sound!!


Do other speakers (that you know to work) perform correctly when you plug them in?

Let me know.

Derek

Mar 06, 2009 | Creative Labs Inspire T3000 Computer...

1 Answer

Because of Gigaware headphones, my speakers dont work


it sounds like the headphones shorted out the usb on your system, you might try some speakers that are not usb and see what you come up with,,,also check and make sur your sound isnt muted on the master control for the volume

Feb 26, 2009 | Computer Speakers

1 Answer

Speakers not working


have you tried upping the volume of your speakers?

Jun 08, 2008 | Computer Speakers

2 Answers

Not turning on.


I have these speakers and I had to dismantle the circuit board to replace some components. I think it was capacitors, but a long time ago....so...I don't remember which parts....most likely same problem....mine are still working now. A good tech should trace power to amp section and signal through amp. ...about $15 reasonable repair....no more.

May 26, 2008 | Labtec LCS 2420 Computer Speakers

6 Answers

Right speaker doesn't work


I had this very same problem and I had my system for about 2 weeks. I have seen a lot of similar posts on this site so it seems that this problems happens a lot. For some reason my right speaker just stopped working so i came to this site for help. I looked at alot of posts and nothing fixed the problem. when i switched the right speaker to the left input it started to work so I knew the speakers were fine. So i finally decided to unplug everything and restart my laptop. Once my laptop rebooted I plugged the sub back into the wall after about a minute of it being not plugged in. Then I plugged all the the wires and volume control back into the sub and turned the switch back on. Make sure the volume control is down when you plug everything back in. Then plug the wire into the device, which in my case was a laptop, and start to play some tunes. Right away everything was working perfectly fine again and no problems ever since...for me atleast.

HOPE THIS HELPS

Mar 13, 2007 | Logitech Z-2300 Computer Speakers

2 Answers

The speakers don't work


Ok There is another chance to work your speakers ,

  If you have your mother board CD , get play that  and  reinstall the sound system .

  I hope it will work ,      please do reply

Sep 06, 2006 | Gateway GMAX 2100 Computer Speakers

12 Answers

Speakers not working, but cables all plugged in...


No drivers for your soundcard, this is a computer issue not a speaker issue, contact dell, if you can understand a word they say, ask them "I have Dimension (model number here), I need to know how to install my sound drivers", if you dont know how to do this.

Jun 21, 2006 | Dell A215 Computer Speakers

Not finding what you are looking for?
Cyber Acoustics CA-3550 Computer Speakers Logo

1,293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cyber Acoustics Computer Speakers Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Carlos L. Burgos
Carlos L. Burgos

Level 2 Expert

508 Answers

buzz flewhart
buzz flewhart

Level 3 Expert

655 Answers

Are you a Cyber Acoustics Computer Speaker Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...