Question about Dishwashers

4 Answers

MAYTAG QUIET SERIES 300 DISHWASHER MODEL MDB7600AWW

Yesterday after the dishwasher was finished it was fashing 9 min on the screen and the rinse light was on. I tried to cancell it but it kept coming back, with the door open or closed.
This morning there is no power to the control panel it is blank.

Jeff

Posted by on

  • 6 more comments 
  • ffzcubpilot May 08, 2008

    The washer starts and then stops dead. I have to recycle get it to drain the water and then I restart. Sometimes it goes all the way thru the cycle and other times it stops again and I have to repeat the 'empty' and start again.

  • toast18 May 27, 2008

    I am having the same problem. 9 minutes on the screen and the rinse light was on. I tried to cancell it but it kept coming back, with the door open or closed.Turn off the break did not help... The next day it was able to run one cycle this started with the 9 minutes flash again.



    Thanks for any help.

  • SSpark Jun 14, 2008

    Door panel display flashes 9 and dishwasher control defaults to Rinse Only. IT's a Maytag QUiet Series 300 model MDB7600AWW about 5 years old.

  • Anonymous Jun 25, 2008

    Same problem....flashing "9" and rinse cycle. It runs down to "0" and shuts off only to start flashing the 9 again. Dishwasher is 6 years old.

  • Anonymous Aug 05, 2008

    I have the same issue. I have a MAYTAG QUIET SERIES 300 DISHWASHER MODEL MDB7600AWW. The rinse only light is flashing, along with a flashing "9" on the screen. I just bought this house a year ago, and I have no clue if it is warranted.

  • spschroeder Aug 25, 2008

    I have the same problem as well. Has anyone found a resolution? Any help from Maytag on this repair? Seems like it should be a recalled part...

  • Anonymous Sep 22, 2008

    Same problem.

  • rudykrista Oct 15, 2008

    I have the same problem. sometimes I start the nine minute cycle and the problem goes away. Then the full cycle operates normally.

    Rudy


×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Order and replace the front panel only - not the control card. This will resolve the problem.

Posted on May 15, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I don't have a solution... I have replaced the control panel twice in the past 7 months AND TONIGHT IT WENT OUT AGAIN... I'm really disgusted with this machine... I always have bought matag's but am seriously considering a change.

Posted on Dec 14, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 33 Answers

My mom had this problem... repair man wanted almost $200 for part (control board) and $150 labor to fix. My mom called maytag (machine is 2 yrs. old) they sent her the new control board for $52 including shipping and my brother installed it in 10 minutes. works fine now. still flashes 9 on occassion, but i am reading that it may be bad control panel connection.. but atleast its working now :)

Posted on Mar 30, 2010

I had the same problem, my dishwasher needed a new brain. Cost around $150 to fix

Posted on Jun 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinking "Normal" light on a Maytag model


Hi


Open the door. Within 3 seconds press the following sequence --Try pressing normal wash, heated dry, normal wash, heated dry, normal wash, heated dry three times within 6 seconds and then press cancel to reset the dishwasher. If that doesn't help then try pressing Saini Rinse, Heated Dry, Saini Rinse, Heated Dry, Saini Rinse, Heated Dry or Saini Rinse, Air Dry, Saini Rinse, Air Dry, Saini Rinse, Air Dry 3 times in 6 seconds and then the Cancel Button. Close the door and press Cancel.
Blinking lights would stop and should be able to use your dishwasher normally. If the light is still blinking try and reset the power to the dishwasher and try again. If still the light is blinking then check for the connections on the keypad, it may be due to moisture or shorted connections on keypad.



Hope this helps... Please post back if you need more information.


Daniel

May 19, 2011 | Maytag Dishwasher

1 Answer

Talking about a kenmore 665.16389300 dishwasher. the "normal wash" button is blinking, but none of the other buttons seem to work and the cleaning cycle will not start when i press the...


Hi
Open the door. Within 3 seconds press the following sequence --Try pressing normal wash, heated dry, normal wash, heated dry, normal wash, heated dry three times within 6 seconds and then press cancel to reset the dishwasher. If that doesn't help then try pressing Saini Rinse, Heated Dry, Saini Rinse, Heated Dry, Saini Rinse, Heated Dry or Saini Rinse, Air Dry, Saini Rinse, Air Dry, Saini Rinse, Air Dry 3 times in 6 seconds and then the Cancel Button. Close the door and press Cancel.
Blinking lights would stop and should be able to use your dishwasher normally. If the light is still blinking try and reset the power to the dishwasher and try again. If still the light is blinking then check for the connections on the keypad, it may be due to moisture or shorted connections on keypad. Hope this helps... Please post back if you need more information.


Daniel

May 18, 2011 | Kenmore Dishwashers

1 Answer

Light is on for heat dry but won't allow me to run a cyle or turn on


Hi




Open the door. Within 3 seconds press the following sequence --Try pressing normal wash, heated dry, normal wash, heated dry, normal wash, heated dry three times within 6 seconds and then press cancel to reset the dishwasher. If that doesn't help then try pressing Saini Rinse, Heated Dry, Saini Rinse, Heated Dry, Saini Rinse, Heated Dry or Saini Rinse, Air Dry, Saini Rinse, Air Dry, Saini Rinse, Air Dry 3 times in 6 seconds and then the Cancel Button. Close the door and press Cancel.
Blinking lights would stop and should be able to use your dishwasher normally. If the light is still blinking try and reset the power to the dishwasher and try again. If still the light is blinking then check for the connections on the keypad, it may be due to moisture or shorted connections on keypad.



Hope this helps... Please post back if you need more information.

Daniel

Apr 17, 2011 | Frigidaire Professional Series 24 in....

1 Answer

Normal light blinks


Hi





Open the door. Within 3 seconds press the following sequence --Try pressing normal wash, heated dry, normal wash, heated dry, normal wash, heated dry three times within 6 seconds and then press cancel to reset the dishwasher. If that doesn't help then try pressing Saini Rinse, Heated Dry, Saini Rinse, Heated Dry, Saini Rinse, Heated Dry or Saini Rinse, Air Dry, Saini Rinse, Air Dry,Saini Rinse, Air Dry 3 times in 6 seconds and then the Cancel Button. Close the door and press Cancel.
Blinking lights would stop and should be able to use your dishwasher normally. If the light is still blinking try and reset the power to the dishwasher and try again. If still the light is blinking then check for the connections on the keypad, it may be due to moisture or shorted connections on keypad.



Hope this helps... Please post back if you need more information.


Daniel

Apr 17, 2011 | Whirlpool Dishwashers

1 Answer

There is water sitting in the bottom after all the cycles finish I tried to cancel and rinse to no effect.


9 times out of 10 there will be debris stuck in the pump impeller... access from the bottom of dishwasher by tilting to side or back... common fault...

Oct 03, 2010 | KitchenAid KUDR01TJ Dishwasher

1 Answer

Washing machine displays an LF error code. Started last week during whitest whites cycle in rinse. I cancelled and just did rinse to finish my load. All other cycles worked and yesterday all started...


LF = Long Fill

LF flashes when the water level does not change for a period of time after the valves are turned on OR water has disengaged the basket but control does not detect a water level change.
Is water supply connected and turned on?
Are hose screens plugged?
Is water entering the tub? If so check pressure hose connection to machine/motor control.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Sep 07, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Hotpoint dwt10 not working rinse aid light flashing


I have DWT10P dishwasher.It is displaying two rapidly fashing E lights (Fast & Delicate )wash cycle.Can you tell me what its mean?

Mar 24, 2009 | KitchenAid 24 in. KUDI01IL - Multiple...

1 Answer

Whirlpool GU2400XTPS rinse only light is blinking


mutiple keys stuck press keys one at a time then hit cancel

Dec 30, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

DW won't drain and "lock" light is stuck "ON"


Joe, see if you can reset the board by pressing heated dry-normal-heated dry-normal..(new board). Old board is high temp wash-air dry-high temp wash-air dry. See if it goes back to normal. If not you probably have a stuck or shorted keypad on the overlay..not the board. Catriver...post back

Sep 09, 2006 | Kenmore 15892 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

3,345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

66433 Answers

Brad Brown

Level 3 Expert

14374 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...