Question about Computers & Internet

1 Answer

CRC error?? hi, i have a vanguard router problemis that,the broadcast is mismatched between 2 terminals(work station).i've found that the router is generated CRC error.i want to know that,this problem is generated by the cause of CRC errors or any thing else??? plz. give solution.

Posted by on

  • arunkumarms Nov 05, 2008

    we have leased line connectivity between two points, network provider is BSNL, in one point I get CRC errors as 400, can you please help -arun


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

"In simple terms, a CRC (cyclic redundancy checks) is bit of mathematics used to ensure that your data is OK when being transfered. It's a checking procedure that quickly identifies when data has been damaged. If you get this message, it means that the file being read by your PC or software is corrupted."

so, yes, the CRC error is most likly the problem.

Posted on May 09, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to do 6455 "Node to Node download" Thanks a

tai sao motorola khong chup hinh duoc mong cac ban giai dap dum` em

Aug 14, 2013 | Arris Vanguard 6455 Router

1 Answer

My lan speed going down.i am using cisco router 881, guide me to troubleshoot this speed issue

this could be MANY reasons....first, how many devices on your LAN ??? If there is a broadcast storm, that will slow things down on your LAN. Very few devices nowadays cause this. Also, from your pc, try pinging your router using an increased packet load. So start of with ping <router ip> -l 8000 and try going up to 20000. In theory, you should not be getting any loss. Responses times up to 12000 should be 4 - 8 ms. Higher response times point to errors on NICs. On the route console, try a show int VLAN <vlan number you've configured for your LAN> and enter. Under the CRC Errors and Interface resets, if you have anything more than 5, it could be a cable/NIC/MTU size problem.

Jul 08, 2013 | Cisco 881-K9 Router

1 Answer

I have problems with my vanguard motorola 6455 "error need coldload" i need help urgent

In main menu type (7.5.y) and the router will be reboot, you'll loose the data and configuration. Re-imagine it, Re-configure it and you'll ready to use your vanguard

Mar 30, 2011 | Arris Vanguard 6455 Router

1 Answer

How do you troubleshoot input errors eth is UP, line protocol is UP Hardware address is Ip address is XXX.X.X.XX, netmask is MTU is 1500 bytes, BW is 100000 Kbit 100Mb/s, half-duplex ARP...

You have input errors but no output errors, and your link is showing half duplex.
The device connected may be set at full duplex, but this is in fact normal for half duplex connections which do NOT allow send and receive at the same time. Ensure both ends are set to full duplex.

Mar 11, 2010 | Adtran NetVanta 4305 Router (1200890l2)

1 Answer

I need the line command set to configurate a Motorola Vanguard 6455, thank a lot...

Open command propmt, type there ipconfig and look for default gateway. Take note of the default gateway numbers and type that on the address bar of your IE browser. There you can setup the device.

Jun 09, 2009 | Arris Vanguard 6455 Router

1 Answer

Router stopped working altogether

You can try doing a master reset. (must refer to owners manual on how to) or replace the entire unit. Most likely the unit has failed.

Thanks, Frank

Apr 02, 2009 | Microsoft Broadband Networking MN-500...

1 Answer

Vanguard 6455: double configuration.

when u reboot your router, at POST type ZAP command.. by this you will reset your password as well as your configuration.

try this and let me know ... wht happen??????

Jan 28, 2009 | Arris Vanguard 6455 Router

1 Answer

New WRT54GS Router, Wired Desktop not working

To do this you would restor it back to factory which means old you programs and documents that have been added will be permatly lost inless you put these files on a usb flash brive or burn them to a cd.

Jan 04, 2009 | Linksys Wireless-G WRT54GS Router...

2 Answers

Vanguard 6455 router lost password

in my experience, any router where you cannot access it, you will have to do a factory reset. Generally there is the small paperclip size button in the back that you press and hold for 10 seconds while the router is on. after that, you release and unplug the router. Press the small button, plug in the router, and hold it for about 20 seconds. Sadly, I have found this my most common and best answer...

Dec 19, 2008 | Arris Vanguard 6455 Router

2 Answers

Restarting device

Generally Yes, when any Systems Settings are "Updated" usually one must reboot any system to cause the system to "Write" and then recognise the new values.

Apr 05, 2007 | Arris Vanguard 6455 Router

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

399 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers


Level 3 Expert

100340 Answers

David Payne
David Payne

Level 3 Expert

14160 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides