Question about Sport & Outdoor - Others

Open Question

New 350 ignite trojan treadmill when switch to start after few second display E1 flashing

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: tredmill error code

Moat likely a problem with the motor control board. See treadmilldoctor.com

Posted on Nov 17, 2008

Ad
  • 64 Answers

SOURCE: Treadmill runs then stops. E1 error and sometimes works fine.

Yes if speed sensor is too far from magnet it will not pick up belt movement. This confuses the computer and as a safety precaution it shuts the machine off. Find speed sensor and check for proper alighment with magnet.

Posted on Jun 08, 2009

  • 1 Answer

SOURCE: tredmill error code e1

Trimline treadmill starts up then code E2 comes up, and the display shuts down. 
Any ideas???

Posted on Dec 20, 2009

  • 33 Answers

SOURCE: I have a BH treadmill that has an E1 Error messgae...

Your problem might be that a magnet has fallen off. Here's an illustrated guide that should make fixing it easy: http://fixmytreadmill.blogspot.com/2010/10/how-to-fix-treadmill-e1-error.html

Good luck.

Posted on Oct 09, 2010

  • 33 Answers

SOURCE: Treadmill cuts out after 10 seconds and gives an E1 message.

Your problem might be that a magnet has fallen out of place. Here's an illustrated guide that should make fixing it easy: http://fixmytreadmill.blogspot.com/2010/10/how-to-fix-treadmill-e1-error.html

Good luck.

Posted on Oct 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E1 error after start


this ERR1 indicates a speed issue. In this case, the motor speed as reported from the optic sensor differs
from the speed setting.
Analysis: Optic sensor signal issue -- Either the optic sensor signal is not right, or it is read incorrectly, or
the signal is not reaching the display. see the diagram attached.
God bless you
8aa471e2-eb3e-4152-9565-99282c83168c.gif

Nov 27, 2013 | Kettler treadmill Pacer

1 Answer

My Trojan treadmill shows E1 error code.. Please advise . thanks


please test the following steps. God bless you

ERR1 indicates a speed issue. In this case, the motor speed as reported from the optic sensor differs
from the speed setting.
Analysis: Optic sensor signal issue -- Either the optic sensor signal is not right, or it is read incorrectly, or
the signal is not reaching the display.
see the diagram attached.6b49b8f5-6e36-4223-8f25-0adeb1611452.giffinally reset the small switch, use small pencil erase for to click. the switch is to side the main power

Aug 24, 2013 | Exercise & Fitness

1 Answer

E1 ERROR on Trojan treadmill


Step 1:

This is probably a1) faulty speed sensor or the speed sensor adjust see the diagram attached..2) Clean it very weel 3) pluged very strong.
1_7_2013_4_47_16_pm.gif

Step 2:

also possibly a a)faulty motor tes the input voltage , if there are the motor need repair see my personal TIPS for motor help. b) lower board, measure the output voltage board for inpt voltage motor, if there are NOT the board is faulty, replace see the block diagram and wiring diagram.
. The error codes will differ between makes and models but could be e1.1_7_2013_4_49_28_pm.jpg1_7_2013_4_49_42_pm.gif

Step 3:

Finally see the video and LUBE the deck belt and rollers bearing too, proceed according.

Jan 07, 2013 | Exercise & Fitness

1 Answer

I got dkcity treadmill model number- DK5320HRP ' When we press start button the motor does not turn and after few second an error E1 showing on the display. plaese if anyone can solve this proble


I got dkcity treadmill model number- DK5320HRP ' When we press start button the motor does not turn and after few second an error E7 showing on the display. plaese if anyone can solve this proble

Jan 02, 2012 | Exercise & Fitness

2 Answers

Tuturi J661F stopped working - Error E1


Your problem might be that a magnet has fallen off. Here's an illustrated tutorial that should make fixing it easy: http://fixmytreadmill.blogspot.com/2010/10/how-to-fix-treadmill-e1-error.html

Good luck.

Apr 20, 2009 | Exercise & Fitness

3 Answers

Error message E1


hi there we have an E1 error after 7 seconds of operation??

Apr 09, 2009 | Exercise & Fitness

Not finding what you are looking for?
Sport & Outdoor - Others Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sport & Outdoor - Others Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

kakima

Level 3 Expert

102366 Answers

Brad Brown

Level 3 Expert

15628 Answers

Are you a Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...