Question about Black & Decker Garden

Open Question

I am trying to use my BD 531 jigsaw (corded) but blade keeps coming out after I start cutting. I make sure is tight when start...old one now discontinued but I very seldom use it and can't find instructions to check. Please help

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 10865 Answers

SOURCE: crooked cuts

The bearings in your saw need to be replaced. I would contact a DeWalt store to obtain the parts or have them do the repair. You have an excellent saw there, well worth repairing. good luck.

Posted on Jan 28, 2009

Ad
  • 1 Answer

SOURCE: Changing the blade in a bosch pst 65 pae corded jigsaw

Pull up the knob on the front at the top of the machine and push the yellow bit forward. Theoretically you should turn the knob anticlockwise three turns but it doesn't seem to make any difference on my one. Then take hold of the blade, ease it forward and turn through 90 degrees. You should then be able to pull it out. Replacement is, as they say in all the best manuals, a simple reversal of the procedure. When you are turning the knob clockwise this time it's supposed to click in place but my one doesn't do this and still seems to work.

Best of luck

Gavin

Posted on Apr 10, 2009

  • 1 Answer

SOURCE: how to change blade on bosch jigsaw GST 80 PBE

I just bought a used one and faced the same problem. What I found in there is a set screw at the bottom of the long shaft. I used a long narrow flat head screw driver. It worked good, but I did have to acuate the trigger to get it the blade near the top of the stroke

Hope that helps.
AG
Porsgrunn Norway

Posted on Aug 15, 2009

Mike258
  • 1498 Answers

SOURCE: jigsaw dc330 blades keep poping out when used

Hi Paul,

When inserting the blade, turn the saw upside down to prevent the blade from moving while tightening.

Before inserting a new blade, check the receiver for obstruction or debris that may prevent the blade from properly registering with the tightening screw.

Make sure the blade is fully seated in the receiver before tightening.

The tightening screws that secure blades on any type of reciprocating saws (Jig, Scroll, Sawzall, etc.) are constantly under stress and do wear out. If the problem continues, it may need to be replaced.

Best regards
Mike

Posted on Oct 29, 2009

SOURCE: my dell inspiron 531 desktop enters auto detect power save mode

start your computer in safemode and then turn off all power saving features

Posted on Apr 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to lock the jigsaw blade to make straight cuts on my Boschest 1587svs?


Use a straight edge guide. Clamp it on the work so the jigsaw can run against it. Be patient and go very slowly.

Mar 04, 2017 | Blade Saws

1 Answer

What models of jigsaw blades are suitable for cutting wood using a Black & Decker DN31-H1 Jigsaw?


Blade can be had at any hardware store or home improvement store. There are a lot of wood cutting blades available depending on the hardness of the wood and how thick the material is

Nov 06, 2014 | Saws

1 Answer

When cutting straight with my jigsaw the blade floats even though it is in the lock position


There is a speed and angle ratio that must be observed . Depending on the density of the material and the thickness. The shoe plate can be raised or lowered to assist with the forenamed floating condition. Proper blade selection and sharpness is essential.

With thick materials pushing the blades design, speed and force must be regulated through patience to provide the accuracy you demand. The complete blade system is another part of your investment . Understanding what and when can overcome fast if problems arise. Assuming all of this is in your tool box. I always have been taught. Only adapt when all reason is exhausted.


The last part I have had happen is vibration and tool integrity. Maintaining a tight fastener system all over the tool by lubrication is paramount from use or lack of it. Preventive measures spot stuff from happening when you are making the million dollar cut. But we all know that. Daily or startup practice. Just like stretching before playing, a great coach takes the time to do it for their selves too.


There are six JS700 models. Here is a place for parts should that arise Black Decker Jigsaw Replacement Parts Repair your Black Decker Jigsaw... . Furthermore, here is some words for those who are new at the application. Take a look. How to Use Jigsaw basic. This next look in video instruction is thorough and shows intermediate techniques with some experienced foundation. How to Use Jigsaw produced by skill. The Woodworker Journal places the top six picks side by side in the last video offered Top Shelf Jigsaw Review . There is one called a "Mafell" which has a so called perfect orbiting system, which some make it, the straight cut King.


I took the time to do this on the first day of summer. There is lots more to discuss. I think you have the most versatile easy to learn tool in your shop. I am almost sure you think so too. Keep humming. Fare. Well.


Mar 28, 2014 | Saws

1 Answer

Oil leak from my Skil Jigsaw and it keeps Jamming when I cut wood


get a nail file and sharpen the blade till you can see your face in it

May 07, 2013 | Skil Top Handle Jig Saws Variable Speed...

1 Answer

I have a craftsman jigsaw(scroll) that I got for Christmas last year. The blade comes out in the middle of my cut some time. Is there a problem with this type of jigsaw?? I have sanded the top of the...


Most of the time the cause for this is applying to much pressure on the blade as you are cutting. Remember, the blade does the cutting and you are guiding the jigsaw around the cut. This can strip the blade and wear the top of the mount. Adjust the way you cut and you should not have any problems.

Aug 26, 2011 | Craftsman Saws

1 Answer

I need to use my late husband's jigsaw but can't get the old, bent blade out. How do I do it and which blade do I replace it with? I need to cut a few cms off the width of a kitchen worktop. I...


Hi Jen,

It depends on whether you have an older or newer model jigsaw. Bosch makes the newer ones with a button you push that will release the blade.
On an older jigsaw, look at the handle from above the jigsaw directly in line with the blade. You should see a screw in the top of the handle. Use a screwdriver and loosen this screw, don't remove it, and when the screw is loose enough, you'll be able to pull the blade out. When you put the new one in, slide it in the slot until it seats.

A rule of thumb is to use the blade with the wider gap and larger teeth on wood, the smaller teeth on metal. Most blades will say bimetal on the metal cutting blades.
Now, the courser the teeth the rougher cut you'll get. So, if you want a nice cut, don't use the blade with the largest teeth. Move down to the next largest.

I don't have a Bosch, so am not sure which codes are for which blades, but you can't go wrong if you go by the size of the teeth.

You didn't say what material the worktop is made of. If it's wood, the second largest toothed blade should be fine.

If you've never used a jigsaw before, I could suggest a couple tips that would help you get a nice job done.
First, put a piece of painters tape or masking tape over where you will cut, draw your line and go easy. The tape will keep the blade from giving you a roughed up top edge.
When you get near the end of the cut, hold a piece of scrap wood flat against the back edge to prevent tearout.
Also, let the saw do the work, don't push it.

Hope this helps, If it does, I'd appreciate a 4 thumbs up, Thanks,

Handie Andie, "woodworker by night"

May 24, 2011 | Bosch Garden

2 Answers

How do you put a blade in a hitachi cj110mv jigsaw


on the front of the saw where the blade is there is going to be a little lever you pull while at the same time push the blade in the blade holder

Jan 16, 2011 | Hitachi CJ110MV D Handle Jigsaw

1 Answer

This jigsaw seems to suffer from the same problem as its predecessor. Whenever i use it to cut through a kitchen worktop or any material it never gives a straight vertical cut through the material but...


I can't speak to the diffuculty you're having with that particular model, as I haven't used it. But in general, the stability of the cut depends upon the guide mechanism of the saw, and a three point guide is better than two point or single point. A three point guide assemble will hold the blade firmly locked when inserted into the column, will have a roller bearing that supports the center of the blade path, and will also have a finger pinching mechanism at the base near the material, so the blade can't waffle in the cut. Aside from changing saws, all I can recommend is that you make sure the base is correctly locked in place at an angle square to the blade, when fully extended. Check this with a small trysquare against the base, and look from both sides of the blade. Some folks will even attach an auxiliary base to stiffen theirs up, though this shouldn't be necessary. Then make sure you're using a sharp blade with the correct tooth count for the material you're cutting, and don't force the cut. Let the saw do the work, and make sure you hold the base firmly against the worktop as you cut. If you force a cut with the orbital action on full, you'll get more deflection.
Other than that, all I can say is that I've had good luck with the newer Bosch jigsaws, and the best cut I know of comes from the Festo, but we're talking serious dollars there.
Good luck.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Dec 19, 2010 | Hitachi CJ110MV D Handle Jigsaw

1 Answer

My original blade broke so i bought a new blade from wickes 10tpi now when i use it i saw on the line i have marked but on the other side of the 2x2 it is about quarter to hallf inch out how can i make...


There are good blades and there are cheap blades. Good blades are straighter but less tolerant of poor technique and so tend to break, cheap blades can and do bend far more. You can keep the blade straighter by not forcing the blade through the work and allowing it to cut at it's own rate and by experimenting with the speed settings on the jigsaw. It also helps if you pick the correct blade for the job: 10tpi is a bit too coarse for ripping a timber batten along the grain but fine for rough cutting chipboard. Also, it's difficult to keep the foot of the jigsaw absolutely level on 2x2 which adds to your problems.

Aug 15, 2010 | Bosch T-Shank High Speed Steel Jigsaw...

1 Answer

Blade wander


a jigsaw is for cutting wavy lines if u want a straight cut use a rip saw with fine blade but you still can use a jigsaw must have sharp blade there is a blade u can get now from screwfix with a triangle spine on the back off the blade to prevent it twisting works fine (also do not push hard on the powertool let the blade do the cutting less likely to wander hope this is of help

May 30, 2009 | Bosch 1590EVSK 6.4 Amp Top Handle Jigsaw

Not finding what you are looking for?
Garden Logo

Related Topics:

636 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Garden Experts

Nick Olsen

Level 2 Expert

183 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Are you a Black & Decker Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...