Question about Universal Remote Control DIRECTV Universal Remote Control

1 Answer

Remote code I have a universal remote that controls my dvr box for my digital cable. My old tv was programmed to this remote however I have a new tv now and I would like to control my tv and cable with one remote. How do I find the right code for the new tv. It is a sony.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

Sony TV codes: 0000, 0080

You can find the remote control codes for different brands of devices from
http://www.hifi-remote.com/ofa/codes-tv.shtml#tv

If none of the codes work then we have two other solutions:

1. Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment ,or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.
If you don't find a code that works, the remote will flash four times when you reach the end of all the codes for this device type.

  1. PRESS the button for the device you want to program, (TV, VCR, CABLE, etc.), then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. (On VCR, LD, and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

2. Learn the buttons from the original

Line up your original remote and the head-to-head before completing the following steps.
  1. PRESS and HOLD the SETUP button until the red LED flashes twice.
  2. PRESS 9 - 7 - 5, the red LED will flash twice.
  3. PRESS the DEVICE key where you wish to learn the function. The next 3 steps must be completed within 10 seconds.
  4. PRESS the button that will receive the learned function, the LED will flash rapidly.
  5. PRESS the button on the original remote to be learned.

Now you can repeat steps 3 through 5 to learn other functions onto other keys or press and hold SETUP until the Cinema's red light flashes twice to lock in your new feature. (If the red light does not blink twice, stop and repeat steps through 6).
To test the new feature, press and release the device key in which the new feature was learned followed by the key on which the feature was learned

More help for programming your remote can be found here:
http://www.hifi-remote.com/manuals/ofa-l.shtml?URC-7800#device

Hope that helps! Should you have any further questions, please feel free to post them here.

P.S. - If you find that the solution/answer I provided led you to, or resulted in a fix, please close the ticket with a FixYa! rating. I would be very grateful for your show of appreciation.

Thank you for using FIXYA!

Cheers!
IrishDruid


Posted on May 23, 2008

  • Swilin Sampson
    Swilin Sampson Jun 01, 2008

    Hello,





    This thread has gone 7 days or more without a response.
    Please close the thread with a “FixYa” or “Helpful” rating.





    Or post back with latest developments, what steps you took,
    etc. and I will assist you further as best I can.





    Thank you.


    IrishDruid




×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm trying to program a magnavox converter box with a universal remote model UR5U-8780L-TWT. I need the code for this please.


Hi Jerry, This is from the link below.........
The Time Warner Cable CLIKR-5 is designed to offer complete control for all digital, HD and DVR set-top boxes. The UR5U-8780L is factory programmed to operate Scientific Atlanta/Cisco and Samsung set-top boxes while the UR5U-8790L is factory programmed for Motorola set-top boxes.
Time Warner Cable CLIKR 5 Universal Remote Control

May 01, 2016 | Magnavox Remote Controls

1 Answer

It's not working what can I do to program one for all controller to rca tv


HI,
The One For All 3 Device Universal Remote Control is preprogrammed at the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola cable box. To control devices other than the default brands, perform the following steps; otherwise skip this section:

HOW TO PROGRAM

1.Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc)

NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step.

( CHECK THE BELLOW ADDED LINK TO FIND THE CODE )


2.On the remote control, press a device key once (i.e., DVD/VCR, CBL/SAT, or TV).

NOTE: To program control of a VCR, PVR (or DVR), TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCRonce. After programming a VCR Combo device, you will be able to control channel selection, volume, and VCR functions.
NOTE: To program control of a DVD Player, DVD Player/VCR Combo, or TV/DVD Player Combo, press DVD/VCRonce. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.
NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR) Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR) Combo, press CBL/SATonce.

3. Press and hold SET until the LED (red light) blinks twice, then release SET

4. Use the Manufacturer's Codes (starting on page 18) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.

NOTE: If the LEDdid not blink twice, repeat steps 2 through 4 and enter the same code again.

5.Aim the remote control at the device and press POWER once. The device should turn off.
If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still doesn't work, try Searching For next code.

NOTE: If the device does not have a POWER key, press PLAY

6. Repeat steps 1 through 5 for each device you want to control. For future reference, write down each working device code following.

Electronics Equipment Repair Center ONE FOR ALL URC3021 UNIVERSAL REMOTE...
Electronics Equipment Repair Center ONE FOR ALL URC3021 UNIVERSAL REMOTE...

Jan 25, 2015 | RCA Remote Controls

1 Answer

Codes for a conect rm500 remote


I have a RCA MODEL TV 27V514T and a conect-it RM500 UNIVERSAL REMOTE CONTROL I just need the code to program my TV. Please help me.

Feb 26, 2013 | Conect It RM500 Multi-Brand Universal...

1 Answer

Need to program a symphonic tv with a oneforall remote urc-4021boo


Hello
Setup codes for Symphonic TV with One for all URC 4021 remote control are:
0180, 0171

The One For All 3 Device Universal Remote Control is preprogrammed at

the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola

cable box.To control devices other than the default brands,perform the following
steps; otherwise skip this section:

[1] Turn on a desired device (e.g.,VCR or DVD player) and, if
applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding.

Highlight or write down the codes and device you wish to program
before starting step 2.

[2] On the remote control,press a device key once (i.e., DVD/VCR,
CBL/SAT,or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo,

or TV/VCR/DVD Player Combo press DVD/VCR once.After programming

a VCR Combo device, you will be able to control channel selection,

volume, and VCR functions.

NOTE: To program control of a DVD Player,DVD Player/VCR

Combo, or TV/DVD Player Combo, press DVD/VCR once.After programming

a DVD Combo device, you will be able to control channel

selection, volume, and DVD functions.

NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)

Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

[3] Press and hold SET until the LED (red light) blinks twice,
then release SET.

Use the Manufacturer's Codes (starting on page 18) to

locate the type of device and brand name and then enter

the first four-digit code for your device. If performed correctly,

the LED will blink twice.

NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter
the same code again.

[5] Aim the remote control at the device and press POWER

once.The device should turn off. If it does not, repeat

steps 2 through 5, trying each code for your brand until

you find one that works. If it still doesn't work, try
Searching For Your Code on next page.
NOTE: If the device does not have a POWER key, press PLAY
OK

Jul 26, 2011 | One For All URC-4021 Remote Control

2 Answers

Need code for magnavox tv urc-4021boo


Hi, the codes you have requested;

Magnavox - 0054, 0706, 0030, 1454, 1254

Instructions to program code:

1. Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc). NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2.

2. On the remote control,press a device key once (i.e., VCR/PVR, DVD, CBL/SAT,or TV).
NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press VCR/PVR once.After programming a VCR Combo device, you will be able to control channel selection, volume, and VCR functions. NOTE: To program control of a DVD Player,DVD Player/VCR Combo, or TV/DVD Player Combo, press DVD once.After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions. NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR) Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR) Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,then release SET.

4. Use the Manufacturer's Codes (starting on page 18) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter
the same code again.

5. Aim the remote control at the device and press POWER once.The device should turn off. If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works.

Feb 12, 2011 | One For All URC-4021 Remote Control

1 Answer

Charter cable box


Could not find box on list but here is your product manual:
http://www.ofausa.com/remote_manual/CTGAE3P%203021%20anual%20booklet.pdf

PROGRAMMING DEVICE CONTROL
The One For All 3 Device Universal Remote Control is preprogrammed at
the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola
cable box.To control devices other than the default brands,perform the following
steps; otherwise skip this section:
1. Turn on a desired device (e.g.,VCR or DVD player) and, if
applicable, insert media (e.g., cassette or disc).
NOTE: Please read steps 2 through 4 completely before proceeding.
Highlight or write down the codes and device you wish to program
before starting step 2.
2. On the remote control,press a device key once (i.e., DVD/VCR,
CBL/SAT,or TV).
NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo,
or TV/VCR/DVD Player Combo press DVD/VCR once.After programming
a VCR Combo device, you will be able to control channel selection,
volume, and VCR functions.
NOTE: To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once.After programming
a DVD Combo device, you will be able to control channel
selection, volume, and DVD functions.
NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.
3. Press and hold SET until the LED (red light) blinks twice,
then release SET.
4. Use the Manufacturer’s Codes (starting on page 18) to
locate the type of device and brand name and then enter
the first four-digit code for your device. If performed correctly,
the LED will blink twice.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter
the same code again.
5. Aim the remote control at the device and press POWER
once.The device should turn off. If it does not, repeat
steps 2 through 5, trying each code for your brand until
you find one that works. If it still doesn’t work, try
Searching For Your Code on next page.
NOTE: If the device does not have a POWER key, press PLAY.
6. Repeat steps 1 through 5 for each device you want to control.
For future reference,write down each working device
code in the following boxes:

Dec 11, 2007 | One For All URC-3021 Remote Control

Not finding what you are looking for?
Remote Controls Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Universal Remote Control Remote Controls Experts

The Knight
The Knight

Level 3 Expert

68223 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Are you an Universal Remote Control Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...