Question about RCA DRC247N DVD Player

1 Answer

Remote doesn't work/message of "root"

The remote doesn't work...changed batteries...opened it up to see if any buttons were pushed too hard. Also sometimes get a message of "root" on the DVD Player

Posted by on

  • DLH5608 May 06, 2008

    the tv says aux so i think it is on the right channel. any other suggestions? thanks.

×

1 Answer

New item when set up is auto or manual for channel the unit will not lock on to the channel that i have set it too. the system runs ok show' es all the channels but then when finished no signal to tv remote fails to operate

Posted on May 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I accidentally programmed the same button for 2 doors and they both open when the button is pushed. How can I fix this?


Is there a battery in it? Remove the battery, count to 10, insert the battery and start again.

Jul 07, 2015 | Chamberlain Klik1u

2 Answers

Just bought a Toshiba refurbished DVD/VCR player. The remote doesn't work at all. I've doublechecked the NEW batteries and tried a tip of pushing EVERY button with the batteries out. Any ideas


1) the batteries will be the same type and full charged
2) clean the contacts battery from dirty, dust, oxide or corrosion
3) retight the spring contacts battery with pliers for a GOOD contacts
4) open the remote.control and clean the keypads switch, from dirty, dust, oxide, Open contacts, or Bad contacts. they emite a good signal infrared from SYScon transmi vs Syscon receiver.
see the block diagram. If doesnot resolve the problem go to the repair shop TV for fix it.
God bless you
8_1_2012_2_24_45_pm.gif

Jul 31, 2012 | Toshiba Televison & Video

1 Answer

Why remote wont work


Change batteries in remote make sure there in right way then point remote at system if doesn't. work then push on buttons a little harder if still don't work may need to check with manufacturer

Feb 08, 2012 | Bose & Wave& Music System

1 Answer

My dvr freezes. i have picture and sound but unable to change the channel or anything dealing with the dvr. i have to manually push the system info button on the box then select done with the remote. ...


Believe it or not, this could be a simple battery problem in your remote. When my battery is low in my remote, some buttons will work and some not. I'd try replacing the batteries in the remote first. If that doesn't work, I would guess that you need a new remote. Sounds like your DVR works fine manually, so chances are that's not the problem.
Hope this helps.

May 14, 2011 | DISH Network DVR-625 DTV Receiver /...

2 Answers

On my wii remote at the bottom of the remote belong 1&2 them lights all flashing and it will not pick up we change the batties still not working can you help me..


  1. Press the Power button on the Wii console to turn it on.
  2. Remove the battery cover on the back of the Wii Remote you wish to sync up, and press the SYNC button just below the batteries. The Player LED will blink.
  3. Open the SD Card Slot cover on the front of the Wii console and press the SYNC button on the inside of the compartment.
  4. When the Player LED blinking stops, the syncing is complete. The LED that is illuminated indicates the player number (1 to 4).

    wiiremotesynchstandard.gif

This procedure must be followed for each additional Wii Remote added to your system.

Nov 29, 2010 | Nintendo Wii Console

1 Answer

Cannot get remote for garage door to work


push the green button on the opener then push your remote button

Jan 25, 2010 | Locks & Locksmithing

2 Answers

Wii remote wont work change batteries and all lights at bottom just keep blinking


Sync it.Open the front cover on your Wii, then push the red button there, then open the batteries cover on your Wii Remote and push the red button there.If this not help press and hold the red SYNC button on console for 15 seconds. This will clear all synced Wii Remotes from the console.Then try to sync Wii Remote again.

Nov 04, 2009 | Nintendo Wii Console

1 Answer

Remote only closes the garage door, will not open it


Anytime a door opens and/or closes randomly or doesn’t work consistently I look for a smashed wire between the motor unit and the wall button.

If the wire is smashed the insulation becomes so thin that power will leak thru the insulation and activate the door or interfere with the remote signal.

Loosen the staples with a small screwdriver and slide the wire about ½ inch to move any areas of thin insulation away from the staples.

The second thing would be a bad wall button or a remote with a sticking button.
Or a remote in someone’s purse that gets the button pushed by other stuff in the purse.

The test is to disconnect the push button wires at the power unit. If the self operation / interference stops you have located the problem. If you reconnect the wires and disconnect the wire at the wall button this will tell you if the problem is the wire or the button.

In your case the expansion of the wall in the afternoon may be enough to cause pressure on the wire to increase the problem – works in the morning but not the afternoon.

Also after you change the batteries you need to reprogram the remotes.

HOPE THIS HELPS

Aug 08, 2008 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Battery does not last


Anytime a door opens and/or closes randomly or doesn’t work consistently I look for a smashed wire between the motor unit and the wall button.

If the wire is smashed the insulation becomes so thin that power will leak thru the insulation and activate the door or interfere with the remote signal.

Loosen the staples with a small screwdriver and slide the wire about ½ inch to move any areas of thin insulation away from the staples.

The second thing would be a bad wall button or a remote with a sticking button.
Or a remote in someone’s purse that gets the button pushed by other stuff in the purse.

The test is to disconnect the push button wires at the power unit. If the self operation / interference stops you have located the problem. If you reconnect the wires and disconnect the wire at the wall button this will tell you if the problem is the wire or the button.

HOPE THIS HELPS

Aug 06, 2008 | Sears Craftsman LiftMaster Chamberlain...

Not finding what you are looking for?
RCA DRC247N DVD Player Logo

Related Topics:

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71736 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Jaime Hernandez

Level 3 Expert

2294 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...