Question about DVD & Blu-Ray Players
I recently bought a TruTech DVD player (Model 008 06 0950). It's a $30. machine, made in Feb., 2008.
Apparently, I touched the wrong button which seems to have enterred a system of menus in which the on-screen display was changed. Not only am I unable to play a DVD now, but the screen appears fuzzy, with some wavy distortion. (I know that I am stuck in the menu section of the unit because I am sometimes able to see that there are a few words that appear to be a menu screen for DVD player settings.)
TruTech Customer Service tells me (on the phone) that I probably need to change the setting to NTSC. (Actually, I think I may need to change the "display size", or both the TV Type and the display size.)
In any case, I cannot see ANY screens nor any DVD that I put into the player - I have not seen the opening screen with the TruTech logo since this problem appeared. I have NEVER deliberately gone to any of the on-screen menus so I have NEVER seen any of the menus that I need to access in order to change the settings. I will need to change the settings in order to be able to see those menus, or to be able to exit those menus and watch DVDs again.
I have tried pushing arrow and enter buttons to try to change the settings or to access a different screen. In this process, I have sometimes changed the screen so that it shows some wavy distorted words on some screens, such as "audio" and "DVD".
I need pictures of the menu screens so that I can begin to figure out what screens I am on and what the potential functions are. I also need someone to explain to me exactly what on the screen is interactive and which buttons I need to push to navigate, first from screen to screen, and then on a screen, and then when to press "enter" to make a change in the display.
To reset Cyberhomes DVD players. Take the dvd out close the tray. then press and hold stop for five seconds.
Posted on Aug 05, 2006
SOURCE: have a daenyx dv-833 dvd player
Hi, Remove the disc from the DVD tray then try pressing the PALl/NTSC button on the remote control three times. If the picture does not return, then you might accidently press the P.Scan button as well. Press the P.Scan button on the remote control three to four times, you should get the picture back. Dont forget to make sure you do not have a disk in the tray. Let me know the outcome so that I can further assist you. Thanks, MIke
Posted on Nov 02, 2008
Somehow we were able to get it fixed ourselves. We pressed the SETUP button on remote, then pressed the DOWN button 4 times then press the RIGHT button, then ENTER button for factory default setting.
Posted on Jan 09, 2009
Give these a try!
Press MENU Enter code 57538
The current region code appears
For codefree/multi-region press 9
Press Open DVD door button
Power OFF and power ON
You could also try this!
Turn player on without disc inside Press MENU button
Enter your region code (See list below)
Highlighted 'region area number' will appear in the upper-left corner (on some players)
Press 9 to multi-region the machine
Turn machine off
Region 1 - 29334
Region 2 - 38767 (or 5 7 5 3 8)
Region 3 - 56732
Region 4 - 76884
Region 5 - 53814
Region 6 - 24462
Have a go and good luck! (:-)
Posted on Sep 11, 2009
If you point the remote towards sensor, simultaneously hold down the number (1, 2, etc) you want AND the enter button for 5 or more seconds it should switch to the number pressed. Remember if you have a second one, make sure it's off or put towel over its remote sensor. Sue
Posted on Sep 30, 2010
Tips for a great answer:
Oct 16, 2009 | TruTech TT320
Jun 16, 2009 | DVD & Blu-Ray Players
Feb 03, 2008 | DVD & Blu-Ray Players
Jan 03, 2008 | TruTech TT1620 DVD Recorder
220 people viewed this question
Usually answered in minutes!