Question about Kenmore Washing Machines

1 Answer

I was doing a load of towels and the the washer stops at the spin cycle

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 245 Answers

Check your lid switch located under the door on the right side. If you stick a flathead screwdriver in the little oval hole and it does not make a clicking noise, than it is bad. If I am correct please rate me. Thanks.

Posted on Aug 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Maytag Atlantis stopped mid cycle


Bad/worn/broken lid switch look at the back of the lid there is a little lid cam there that hits a switch,if this switch isn't engaging it will do just what you are describing.use a small screw driver to push the button in and see if it starts.

Sep 03, 2009 | Maytag Atlantis MAV6000 Top Load Washer

2 Answers

Whirlpool Cabrio agi stops after wash cycle


you may need a new timer. yes have it looked at.

Jun 01, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Washer stops during rinse cycle and isn't easily restartable....


Sounds like the contacts in the timer has a problem. Unplug washer. Remove the back of the washer and spray WD40 in the timer. Put towels around and under to to collect excess runoff.
Rrotate washer dial 25 times and spray some more wd40. Rotate 25 times again. Do a wash load. If it works put everting back together.

May 04, 2009 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Maytag top loader stopped during spin and now won't start.


ok check the lid switch,,did it knock it out of place,,unplug and take back off ,,,

Jan 05, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

GE model WCVH6800JMS front load washer spin cycle


My washer is 1 1/2 years old and I have the same problem.

Nov 11, 2008 | GE WBVH6240F Front Load Washer

1 Answer

Beach towels sopping wet after machine done spinning


The washer will not proceed into high speed spin with just two large beach towels in the basket. The washer is detecting a out of balance condition, and remains in low speed spin. Solution? Try adding more items into the basket. With only two towels, there is not enough mass to balance the washer. With more clothing or towels, there is more items for the machine to balance, and reach full speed spin.

The only other thing that could cause this, would be if the water in the tub is not completely draining in the time allowed. This washe does not have a cleanout, and checking for an obtruction in the pump is difficult. I would go with the more clothes first, then see.


Sep 25, 2008 | GE WSXH208A Front Load Washer

1 Answer

Washer turns slow loaded or not


front load machines will normaly spin slow on first part of spin cycle this helps distribute load evenly before hi speed spin also if load is extermely off balance ..a large towel with load of light fabrics will never spin to full speed due to off balance produced by wet towel hi speed spin is normaly acheived in last 3-4 min of spin cycle

May 11, 2008 | GE WBVH6240F Front Load Washer

1 Answer

My old Hoover top loader Washer is noisy & doesn't spin out properly - how can I fix it?


Sounds like the switch which cuts the machine off when the load is unbalanced. My guess is that: This switch is being triggered too easily The springs holding the bowl up are either stretched or one is broken; The machine may not be level.

Mar 30, 2007 | Hoover HTC243 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5474 Answers

Mike Squire

Level 2 Expert

391 Answers

Robert Rankin

Level 2 Expert

338 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...