Hi, used Doro 5065R +3 for year, found that the battery of the handsets were end of life, called Doro and advised to take the battery from **** Smith. After replaced with DSE (brand name) NiMH rechargeable batteryHR03 1.2V 700mAh 70AAAHC, the charging seems alright, the signal shows strong but it drops out within 10 seconds on in-coming and out-going calls. Any reason for that ? I haven't kept the old battery but I can remember that was 500mAh, DSE told me that's not a problem. Please advise.
Re: Doro 5065R +3 not working after replaced battery
I have replace my doro batteries with Duracell rechargeables, just make sure you fully charge them before you put them in the handset. If you find after a time that the charge goes again, charge them again (in the charger you buy when you buy the batteries)! Hope this helps. PS, do you know how to turn the answering machine on?
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones). click here to download the app (for users in the US for now) and get all the help you need. Good luck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
1.) The handset battery pack has to be properly charged in order to set any of the handset settings...if the battery pack in the handset is not holding the charge ~ then
2.) The rechargeable battery in the handset is at its end of life and will need to be replaced.
Open the battery comparment on the handset. Under the
battery there should be a small sticker with the model
number. Take this number to www.manualslib.com and
you'll be able to download the original users' manual....
which will then answer many questions.
On the Galaxy display you could see what is the remaining battery life time as calculated by the software. Normally after you replaced the batteries you are supposed to reset this counter using specific software by the manufacturer. According to your information you have replaced the batteries 3 times in 5 years period. This is not normal. Nevertheless since the last replacement in 2008 it appears that the battery are now reaching the end life, which is generally 3-5 years life expectancy.
I would review the following of the assumption that the UPS is fully operational and the charging system is working.
1. Do a load test or a battery impedance test to verify the batteries are good 2. I would look at the battery life time specification, whether it is 3-5 years, 5-7 years ect. 3. Check the room temperature, every 10 degrees Celcius above 25 deg reduces battery life time by half 4. Check the number of power failures/ duration of these power failures and if possible what load were on the UPS at the time of the power failures. I hope this will help. If all verifications are to specifications, then most likely it is a software problem
This is because the extra handset might have not been registered with the base unit.The headset should be register to use the headset with that base unit.
To register the handset to base unit please follow the instruction:-
On registration the handset is allocated a handset number for use on the new base unit, the handset numbers are 1-5.
1. Press and hold on the base unit until starts flashing. Registration mode will remain active for approximately 3 minutes. 2.Press and hold both together until you hear a long beep.
3.Select the base unit you wish to register by pressing the corresponding number button 1-4. 4. When PIN is displayed, enter the units PIN number (0000 for this model). 5. If the registration is successful the handset will return to standby mode in a few seconds. Thanx
Problem fixed.......after a call this morning to Doro tech support. It was a simple fix..........simply hold down the # key to lock or unlock the keypad. Unfortunately I had overlooked that section in the manual.