Question about Dell POWEREDGE 2400 Server

2 Answers

Beeping Upon Bootup

Hey, my Poweredge 2400 has started beeping upon powerup and nothing will appear onscreen...I'm wondering if the power supply might be going? The green light on the power supply is on continuously, but the red light below blinks every few seconds and it seems that the beeps might be corresponding to the blinking red light. Also, no lights turn on on the front of the server tower. Can anybody help?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Hi,PE2400 using beep code and message error for troubleshooting.if you want accurate which part problem checking using Dell Diagnostic 32bit Diag.

Posted on Jul 29, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Dependent on how many beeps you hear is dependent on what might be the problem. A fuller explanation from pushing the power button to nothing happening would be more than helpful. Beeps in a Poweredge can mean motherboard, memory or as you said power supply problems.

Posted on May 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Dell Poweredge 1550 won't connect to the screen. It also constantly beeps upon startup


Is it in a 1, 3, 2 beep pattern (beep....beep, beep, beep........beep, beep)? If so, the memory is either not seated well or may be bad. Try reseating your memory. If it continues, try with one stick at a time just to see if it will boot up with a display.

Thanks,
--Brian

Nov 02, 2013 | Dell PowerEdge Computers & Internet

1 Answer

Dell PowerEdge 2300 Server won't boot


To power off using the power button, press and hold in for more than four seconds.

However this is not solving your problem of not booting, needs some more information. Such as Beeping noises, number and length of beeps. Or any LED.s flashing?

Aug 16, 2012 | Dell PowerEdge 2300 Server

1 Answer

Dell Poweredge 1800 server not start, i press power button but nothing hapened


Your Model of Dell Poweredge 1800 server may not have a redundant power supply. The power supply is the most like cause of the problem. order a replacement power supply and replace the faulty unit.

Oct 17, 2011 | Dell PowerEdge 1800 Server

1 Answer

Poweredge SC 1420 won't come on, it keeps blinking an orange light on the power button and the lights below the power button the first 3 indicator lights are orange. I tried unplugging and plugging it...


hi,
I have several of these and most often there power supplies blow. since they come by default with only one powser supply. the system won't start
I would start there as most other problems will generate beeps.

GL
hope this helps

Don't forget to vote for me
Thank You
Jammer

Aug 17, 2011 | Dell PowerEdge SC1420 (SC1420MIN) Server

1 Answer

Hello our power edge 6600 is beeping and amber


Beeping usually means that you have a defective memory stick which is shorting out your power supply.

Aug 16, 2011 | Dell PowerEdge 6600...

1 Answer

I was just adding more storage to my pe 1800 and it started beeping. i.e long beep stop and then beep again. four amber light were on from the hard drive bay 2 to four being the new bay for the new...


A Blinking Amber or Yellow power button means that the power supply is receiving power from the source but is unable to properly distribute it to the components. This can be caused by a defective power supply or a defective motherboard. Just to make sure that nothing else is causing the problem, remove any PCI cards like modem, video card, sound card, etc... Remove the memory modules and disconnect cables to CD/DVD drives. Look at the USB ports to see if any are damaged. Beeping usually means a memory issue.

Jul 06, 2011 | Dell PowerEdge 1800 Server

3 Answers

Dell PowerEdge 1600SC Server occasionally beeps when running


Check out this site:

http://bioscentral.com/postcodes/dellbios.htm

Write down the exact number of beeps and how long they last to find what the error means. The are call BIOS post codes and they resemble Morse Code. (ie. one long, 3 short, 2 long = RAM issue) Good luck!!

Sep 26, 2008 | Dell PowerEdge 1600SC Server

1 Answer

Beeping PowerEdge 1300


When a Dell server beeps in every 3-5 second that mean it comes from Raid controller.
Dell calls PERC Controller.
It usually reason of a disk failure.

Install open manage server administrator on your server.
See which disks are failed ?

Try to run Power edge diagnostics on the failed disk.
If it passes the test reseat the disk.
if it fails disk has to be replaced with a new one.
If passes the quick test, reseat the disk and update disk + perc firmware and driver to the latest level. that will solve the problem!!

99% beeping comes from perc controller because of a failed HDD

cheers

Aug 18, 2008 | Dell PowerEdge 1300 Server

1 Answer

Constant beeping


I would first check that all the fans are turning when you first power it up. It may have fan speed sensors on them, and one or more fans aren't coming up to speed. I would check the CPU fan(s), as they are usually smaller, and tend to go bad before the other larger ones.

Feb 22, 2008 | Gateway 960 Series (gtwy960) Server

6 Answers

No Video Signal on 1600sc


Disconnect from the network and all other accessories, and power up the system, this might be due to a faulty device attached to the system, eg: when you connect a usb faulty device the boot takes very long time, sometime it does not boot up.

Dec 30, 2007 | Dell PowerEdge 1600SC Server

Not finding what you are looking for?
Dell POWEREDGE 2400 Server Logo

994 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18333 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you a Dell Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...