Question about GE Spacemaker WSLP1100D Top Load Washer

2 Answers

"Dr" error code

My washer keeps stoping just before it is able to completely drain. The "dr" shows up and then to keep it going i have to press the start button again and then it adds more time on the cycle and keeps draining. This usally happens once or twice per load. I always empty the lint traps and i don't over fill it. What am i missing?

Posted by on

  • 1 more comment 
  • titi8399 Oct 20, 2008

    I am having the same problem with my washer it is displaying "DR" the washer is fairly new! This has been going on for a few days- it displays "DR" and beeps!



    HELP

  • Anonymous Jan 16, 2009

    I have the exact same problem. It makes a horrible crunching noise and displays "dr" and won't drain

  • henrietr9 Mar 24, 2009

    The machine goes through a normal wash cycle
    from 53 minutes to 28 minutes. At 28 minutes the machine starts to drain for
    about 5-6 minutes, but the timer stays at 28 minutes. At which time a
    "dr" code appears, the machine beeps and the machine stops.



     


    If the machine is reset, it starts at 22 minutes
    and goes through the 2nd wash cycle. The machine works fine from 22 minutes to
    13 minutes, then it repeats the above process.



     


    When I manually set the machine for the Rinse
    cycle, it starts at 13 minutes and drains for 3 minutes, then stop at 10
    minutes.



     


    If I set the machine for Spin, it starts at 13
    minutes and the timer stops at 10 minutes, but the water continues tickling out
    for another 5-6 minutes before the "dr" code appears and the machine
    stops.



     


    As a test, I manually set the machine on Spin about 20 times. Once ALL
    the water is drained the machine will spin, and spin and spin; Until a new load
    is started..



×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 5 Answers

Your pump is either bound up with something in the chamber, or there is something in your discharge hose blocking the water from escaping.
Look on the back of the washer, and unscrew the circular port in the bottom right corner. (Keep an 8x13 baking pan underneath, water will escape once you open the chamber). Check if there is anything in the chamber that is binding the impeller. If not, remove the metal back and check that all three of the hose connections to your pump are open and have no debris/ change, etc. If there is nothing binding your pump in any of those locations, your pump motor may be failing. I would suggest calling someone out to assist you.

Posted on Jun 19, 2008

  • garnet_mommy
    garnet_mommy Jul 01, 2012

    Glad we found this site. Mine was doing the same thing and we tried this suggestion and then for good measure emptied the lint trap inside and it worked like a charm. Thanks Chris for putting this on here.

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

It was the kink in my hose.
i just moved my washer to a different location in my apartment, and suddenly started to get the "dr" message, and as others have described, it would get to 13 mins and then stop. i came here to find out what "dr" meant, then upon reexamining the back, i found that there was a big old kink in the base of the hose where it met the machine. i finally figured out what the hooks on the upper back were for. i unkinked the hose, inserted it into one of the hooks to keep it straight, and suddenly the drain which had been a trickle turned into a blast. problem solved. (for me that is.) my washer is now happily on its way to the end of the cycle.
brian

Posted on Aug 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Our dishwasher won't drain completely. I ran it through a regular cycle but it was left with water in the bottom.


Have you tried canceling the cycle? To cancel, turn the on/off switch to on, then press and hold for three seconds the two buttons labeled "Cancel Drain". Keep the door closed for the next minute so that the dishwasher can complete the cycle. During this time the pump will remove any water from the washer. Also you will notice that Bosch dishwashers always leave a little water in the system to keep the seals from drying out and going bad.
Hope this helps

Jan 20, 2013 | Bosch 24 in. SHE44C02UC / SHE44C06UC /...

1 Answer

Why does the dr light keeps binking


Hello Gene Frank - Typically error code DR indicates an issue with the door switch and wiring not communicating correctly or closing properly. Try resetting the washer by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and if it proves to be ineffective, contact a professional to move forward accurately.

Nov 30, 2012 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Error code DR comes up on my Frigidaire Affinity and won't keep running


It is telling you there is something wrong with the door lock assembly. You will probably have to replace it, but check it first for a broken wire or some other problem that you can fix.
Here is a link to the part if you need it.

Here is a link to a service manual for your machine that will take you through the testing and repair process.

http://www.emaservicetips.com/pdfs/778_5995456851_Affinity_washer.pdf

Oct 16, 2012 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Affinity frigidare front load washer won't start. It beeps with message flashing (DR)


Hello zabbster - Typically the DR or DO error code indicates that the door switch is not closed. Make sure that the door lock is completely closed. If the door is closed, make sure the door latch is not broken. If the latch is broken, you may possibly need to replace the door lock switch.

Sep 25, 2012 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Washer isn't draining properly. Cleaned out filter but keeps flashing numbers.


My duet is also doing that. The error code that I get is F02. If you press the cancel button twice, it will cancel the error code. Then press and hold the start button until the door locks again. It should continue on the cycle. If not, press cancel once and put the dial on 'drain and spin' to complete the cycle. I think the problem is probably the computer control module, but I am hesitant to spend the money on the part which is about $150 without labor, because my washer is 7 1/2 years old. Replacing the part does not look hard to do. There is a You-Tube video that shows how to take your duet apart and put it back together which shows the computer control module.

Nov 12, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Have Neptune FAV6800AWW top load, washes when it gets to the rinse cycle it stops with water in. If we remove the clothes and wait a while we can get it to complete. The code we are getting is DR which...


Are you sure the error code is DR? Could it be DC an unbalance error code. Google ""16022808.pdf"" to find. Is the washer banging around in Spin Cycle? If so this is a Clutch Pulley issue.

Google this ""Neptune TL Washer FAV6800AWW"" a forum where I help owners of the FAV6800A and FAV9800A machines.

DR is not a listed error code in the FAV6800A/FAV9800A Service Manual.

Aug 27, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Dr error code


“do” or “dr” - door problem. The door is not locking, the control is not able to confirm the door is locked. Might just be corrosion on the door lock connection. Or a bad door lock OR an item in the door keeping the door from locking. Manual and more here

Aug 15, 2010 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Maytag top loadind washer. Won't stop filling up.


Make sure your drain hose to the drain pipe is higher than the water in the tub if not it will keep running and going out the drain.
Also try taking the hose off the level switch and blow in it to be sure it's not stoped up. If is it won't let the level sw cut off. air should go through it. Good luck
When you unpluged the power and it ddn't keep runing the water valve should be ok.

Mar 25, 2010 | Maytag PAV2300 Top Load Washer

1 Answer

Error Code "dr"


Dr means door problem, either some clothes is keeping it from shutting or the door switch is bad 1ff09a4.png

Mar 05, 2010 | Frigidaire Affinity ATF7000ES Front Load...

1 Answer

Code 40


According to the Whirlpool installation and maintenance manual:


F _ _ “F##” code
Press PAUSE/CANCEL once to clear code.
Press START. If code appears again, call for
service.



Sep 24, 2009 | Kenmore Oasis HE 27082 Top Load Washer

Not finding what you are looking for?
GE Spacemaker WSLP1100D Top Load Washer Logo

4,815 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Tim Whalen

Level 3 Expert

3069 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...