Question about Encore Computers & Internet

1 Answer

Hello guys.. i have this encore wireless router its working fine no problems at all.. now my problem is (i forgot the IP of my router, coz i disabled the DCHP server, coz am using a static one.. how will i find or search my IP of the router so i could get in the menu and change the configurations without reseting the router, can anyone please help me out of this problem? are there any utilities for this so we could view the IP of the router, thanks so much in advance..

Posted by on

  • victor jr marmito Aug 25, 2010

    by the way am using my encore wireless router as my link to the other house.. the setting are point to point coz its my link to the house.. now my problem is i forgot the IP of the two encore

  • victor jr marmito Aug 25, 2010

    am using my encore router as my link to the other house.. my setting is WDS.. so i disabled the DCHP server, den am not using the WAN, am only using one of the four ports coz it is set as a local link to my other house its just 40meters away from the main.. my problem now is i forgot the ip both of the encore as my link.. are there any utilities for this so i can see my ip and get in to the menu so i could change my settings..

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,566 Answers

Have you tried doing an ipconfig /all under the command prompt?Can you tell me what are you seeing under the Gateway?

Posted on Aug 25, 2010

  • 7 more comments 
  • lyzias morato Aug 25, 2010

    Have you tried going into:

    http://192.168.1.254

    or

    http://192.168.1.1

    If you have not changed anything on the IP setup of the router, either one of that is the default IP. Let me know about the results.

  • victor jr marmito Aug 25, 2010

    i changed it.. i change the ip of both router, den i write it down on a piece of paper then i lost it.. huhhuhuhu.. right now its running in a good condition both of them no problems at all.. i just want to have some settings to be change.. den how could i get in to it dat i forgot the ip of the router, hmmmp i already put the routers above my roof coz i attached them with an xternal antena..

  • victor jr marmito Aug 25, 2010

    i also have here an ASUS WL-320ge.. it has an utility to view for the ip so there's no problem in writting it down on a piece of paper for the ip coz it has a software.. i wish encore have these kind of software also so its easy for us to search the ip of it.. =)

  • lyzias morato Aug 25, 2010

    Okay, on the command prompt, type:

    ping -r 1 www.yahoo.com

    SAMPLE results:


      Reply from 66.94.230.43: bytes=32 time=294ms TTL=56

      Route: 209.179.21.76

      ...


    the IP address after "Route:" (209.179.21.76) corresponds to the router WAN address.



    Can you try? and then visit the said route, Just addhttp://.

  • victor jr marmito Aug 25, 2010

    i type on command prompt ping -r 1 www.yahoo.com

    pinging any-f p.wa1.b.yahoo.com [209.191.122.70] with 32 bytes of data:

    request timed out
    request timed out
    request timed out
    request timed out

    thats the result

  • victor jr marmito Aug 25, 2010

    i type on command prompt ping -r 1 www.yahoo.com

    pinging any-f p.wa1.b.yahoo.com [209.191.122.70] with 32 bytes of data:

    request timed out
    request timed out
    request timed out
    request timed out

    thats the result

  • lyzias morato Aug 25, 2010

    Can you try to visit this link:

    http://checkip.dyndns.org/

    And then use the result you are going to get there and put it in a browser as well.

  • victor jr marmito Aug 25, 2010

    thats the ip of my main router, thats not what am looking for, hmmp =)

  • victor jr marmito Aug 25, 2010

    i guess i have to climb back to my roof and reset everything then.. whew! =)

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I installed this router on repeater mode, connection to existing router and signal is perfect but have no access to internet... in the access router the internet access is perfect. please let me know how I...


this is from Encore-usa.com

How to use ENHWI-N3 / ENHWI-N34D / ENHWI-2AN3 / ENHWI-2AN34D / ENHWI-3GN3 as a Repeater?


  • For Advance Users, you can download this document.
  • The reason why people use a Encore wireless repeater is because some wireless remote client computers are out of range from the main network's access point (wireless router), or the wireless client is in the dead spot or the device you want to share to the network have no wireless interface card.

    The function of a wireless repeater is basically to extend the wireless signal coverage. Wireless repeater does not authenticate, screen, secure, connect to the internet, give IP address to clients, broadcast names, etc., these are the wireless router's job. Repeater only repeats what the main wireless router does to the wireless clients.

    Checklist:

    • You should know the wireless security type of the existing wireless AP/router, is it a WPA, WPA2 or a WEP?
    • The wireless security key, or password or passphrase of the existing wireless router
    • Your existing wireless router's SSID
    • We recommend that the existing network you are about to add the Repeater on have a DHCP server running and able to lease IP address to all network clients. If you are not sure about this, please ask your ISP or the person who installed your network.

    Hardware Checklist:

    • Computer with wireless device turned off. This is only to set up the repeater, once finished the wireless can be turned on again.
    • The computer must have an available RJ-45 network interface card and web browser installed.
    • A working wireless router or Access Point with one available RJ45 port
    • RJ-45 UTP/TP Ethernet LAN Cable
    • The Encore Router is set to factory default. If your Encore Router is brand new and just pulled out of the box, no need to reset. If changes were made to any settings to the Encore Router before, make sure you "hardware reset" the Encore Router to the factory default settings. Check the User's Manual on how to "hardware reset" the router.

    PROCEDURES:
    1. Hooking up hardware connections:

    1. Both PC or Laptop and the Encore Router should be turned-on.
    2. Disable the wireless client from your PC or laptop computer (if not done so)
    3. Connect the Ethernet cable to the PC or laptop computer and the Encore Router. (This can be done while PC computer and router are turned on.)
    2. Switching mode from AP Mode to Repeater Mode
    1. Using your computer's web browser such as Internet Explorer or Safari Firefox, enter 192.168.0.1 to the address field then hit enter. You should see the Encore Router's User Interface screen still in the AP Router Mode
    2. On the upper right corner of the user interface menu, click on the drop down menu and select "Repeater Mode". Click the "OK" button to the warning box. Wait around 35 seconds until your screen comes back to Encore user interface screen, this time the screen is now in the Repeater Mode. If for some reason you were asked by the repeater to enter the username and password, enter the default username and password (admin/admin) and your Encore Router is now in Repeater Mode.

    NOTE:
    As of this moment your repeater is not connected to any router or network. It has to be configured further to be able to be connected to your current network and access point router.
    3. Connecting your Repeater to your existing network access point or router:

    1. As soon as the Encore Router switched to the Repeater Mode, you should be able to see the same Utility Screen with fewer selections on the left pane.
    2. From the Main Menu screen click on "Wireless" located on the left pane.
    3. Click on "Site Survey" button, a new Window dialogue box will pop up showing a list of Access Points reachable by your Repeater
    4. Check your existing network's access point SSID then click on the radio button that corresponds to your access point router then click "Connect" button.(If you can't find your existing AP router, click on "Refresh" repeatedly until your access point show up, or your location is too far from your existing AP router).
    5. Click on the "Encryption" drop down menu, select your existing access point wireless security, enter your existing router's wireless security key or passphrase then click "Apply". If you get a FAILED message, repeat this procedure again, a wireless hiccup might be interfering, otherwise you now have a working Repeater.
    6. Check your repeater connection by going to your internet browser and open a web page of your choice. If successful your new wireless repeater is working.
    7. Disconnect the Ethernet cable and setup your computer back to its original wireless settings. At this stage, the Repeater is now invisible to any wireless client computers. When connecting a new wireless client within the repeater's wireless range the process is the same as there is no Repeater device at all, the SSID of the wireless router will just be extended in range around where the Repeater is physically located.
    4. Connect your remote wireless client to your wireless router
    1. Using your wireless client utility program, look for your existing router's SSID and connects to it, if this is a new client you will be prompted with the wireless security key. Your repeater is invisible to all wireless clients. All it does is to repeat the wireless router signal as it is to extend its range. Once you have converted the Encore Router to Repeater and successfully connected to your existing router there will be no more configuration needed to the repeater. If you happen to see two identical SSID's of your existing router, this means your wireless client is within the same range of your existing router and the new wireless repeater, then your client don't need the repeater's service.

    NOTE:
    If you are using Windows 7 and your existing access point security wireless is set to WPA2 (AES), make sure your Windows 7 wireless security type properties is set to WPA2-Personal. To check go to Windows 7 Wireless Network Connection, look for your REPEATER router, right-click on it then click Properties, check the settings in the "Security" tab.>

    NOTE:
    When checking the wireless site survey, you may see two routers with the same SSID (names), these are your Access Point and the REPEATER tied together. This also means you are within the reachable range of both Access point and REPEATER.
    5. To check the Repeaters user interface

    At this moment, the Repeater is invisible to any client. The client's IP address is drawn from the DHCP server most likely to be also your wireless router. Therefore the IP address of the repeater is also invisible to the clients. Follow steps below:

    1. Disable wireless connection or turn off wireless in the client PC computer
    2. Connect Ethernet network cable to the RJ-45 port of the client PC computer
    3. Connect the other end of the Ethernet cable to one of the LAN ports of the repeater.
    4. From your computer, set the network card IP address to Static IP Address entering 192.168.0.102, Subnet Mask 255.255.255.0, leave the rest as blank.
    5. Open IE or Internet explorer or any other web browser software and run 192.168.0.1, you should be able to see the Encore Repeater user interface screen. (Changing any settings in the repeater may affect its performance)
    That should help :)
    Christopher

    May 15, 2012 | Encore Enhwi-2an3 Wireless-n Router

    1 Answer

    I forgot my username and password, now i can't log in. How can i setup my router again? I'm using a ENHWI-N3 802.11 n Router


    First press RESET button for 10 seconds it is in back side of router.Then all settings defaults.Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi . Let me know if you need further assistance. Thanks for using FixYa.

    Oct 16, 2010 | Encore ENHWIN3 Wireless Router

    1 Answer

    Installing encore enhwi-g2 router wuithout cd rom


    You can configure the wireless router from unauthorized access by connect a LAN cable from the computer to the router and open a browser and enter the router's configuration URL IP address.
    To secure your wireless network from unauthorized access please click on this link and follow my instructions :-
    http://www.fixya.com/support/r3559128-wireless_router_security

    Mar 07, 2010 | Encore ENHWI-G2 Router

    1 Answer

    I'm can't ping ddns ip from outside


    Access the router's Setup Page and Disable the "Block Anonymous WAN/Internet Request."

    Sep 23, 2009 | Encore 802.11G WIRELESS LAN ROUTER...

    1 Answer

    It cannot detect the wireless detection


    Hello Friend

    Below is the link of User manual of Encore wireless router ,
    A short reading of topic "Installation setup" of Wireless router Manual will give you a cross check from your configuration setup.

    http://www.encore-usa.com/download/manual/ENHWI-G2_Manual.pdf

    , Also check your Wireless Receiver card is properly working or not


    Sep 06, 2009 | Encore 802.11G WIRELESS LAN ROUTER...

    1 Answer

    Can't connect to the internet


    Try to disable any firewall you have on your computer like windows firewall or any third party firewalls like zone alarm, norton and mcaffe

    May 09, 2009 | Encore 802.11G WIRELESS LAN ROUTER...

    2 Answers

    WRT54G router working fine but need to turn on security.


    with the wrt54g you need to open a internet browser and navigate to 192.168.1.1
    a security screen will pop up to which the username is "admin" and the password is either "admin or blank, (unless you specified otherwise when running the install.

    once in click wireless then security in the sub menu (under the wireless link you just clicked) then fill in the boxes

    Mar 01, 2009 | Linksys Wireless-G WRT54G Router

    2 Answers

    Wireless and internet


    1. Make sure that wireless settings are properly synchronized.
    >> ssid/security key.
    2. Check your computers wireless connection status
    > Make sure that it is set to "obtain ip address automatically)
    3. If still not working if computer is set to obtain ip automatically, try assigning static ip on wireless pc
    > You need to know your router's ip address and dns
    4. Disable firewall on wireless pc.

    Jan 23, 2008 | D-Link RangeBooster G WBR-2310 Wireless...

    1 Answer

    Please help I can't conect to Router MR814V2 with wireless card Encore ENPWI-G2


    Hi,

    On Windows XP, the OS will prevent a connection to an unsecured wireless network such as what you have.

    You can try:
    Double click on the red WiFi icon, click on the "Change the order of preferred networks",  Click on "Add", type in the Network name (SSID) of your router (you can get this by using the connected PC and log in to the NetGear's Webbased Interface), set Network Authentication to "Open", set Data encryption to "Disabled",  OK, reboot your PC.

    Alternately, you can set the PC where the Encore ENPWI-G2 card is connected to manual configured settings rather than Auto obtain. Follow what is in the connected PC's settings except that the  last number of the IP add be different (ex. connected PC > 192.168.0.100, set the unconnected PC to 192.168.0.101, all the rest subnet, default dns be the same. Of course the 101 must not be in use, if double IP add, change to 102).

    In some instances, you may need to use the Encore WiFi configuration utility (normally comes with the drivers in the installer CD) rather than the Windows buil-in WiFi Config utility,

    Hope this be of some help/idea. Post back how things turns up or should you need additional information.

    Good luck and kind regards.

    Oct 10, 2007 | NetGear MR814 Wireless Router

    Not finding what you are looking for?
    Computers & Internet Logo

    Related Topics:

    152 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Encore Computers & Internet Experts

    Doctor PC
    Doctor PC

    Level 3 Expert

    7733 Answers

    Michael Galve
    Michael Galve

    Level 3 Expert

    1269 Answers

    Prashant M
    Prashant M

    Level 3 Expert

    2260 Answers

    Are you an Encore Computer and Internet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...