Question about Baby Strollers

2 Answers

How to dismantle little tikes junior activity cube

Little tikes activity junior cube.
has 4 sides and a slide.
really having problems to dismantle.
any ideas?

Posted by on

  • Anonymous Jun 04, 2008

    Try using a rubber mallet to pound the pieces apart. Hope this helps. I have this cube, but my pink slide won't stay up. Is there a part that I'm missing?



    Michjperry@comcast.net

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

At the opposite side to the slide you should see 4 dimples, these should have screws in them, possibly behind a plastic cap.
Take these out, flip the cube onto its side, holding the sides, push (or kick or use the mallet) to get the end piece moving, (there is a dimple which locates into the side which makes this difficult)
Once one side is out, the middle bits should come out easily.
The front (slide part) is assembled the same way.

Hope this helps.

Posted on Apr 08, 2010

Liquid dish soap

Posted on Jul 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Little tikes replacement parts


Hi Marybeth,

We'd recommend you contact Little Tikes direct -

Contact us littletikes co uk

Mar 24, 2014 | Baby Strollers

Tip

HOW TO FIX BUGABOO WHITE SEAT BUTTONS




To fix it yourself, you need to disassemble the buttons, which can be done with two screwdrivers one a thin slot type the other a Phillips. Here is the process: 1. On the other side of the white button unit is a screw. Remove it using a Phillips screwdriver.
macnutz_25.jpg
2. You'll now have a black housing with a white button held in by three white tabs. 3. Free the white button from the housing by pressing inwards on each of the three tabs with the slot type screwdriver.
macnutz_26.jpg
4. You'll now have a black base, a spring and a white button. Pay attention to how the two black parts align to each other so you re-assemble it correctly.
macnutz_28.jpg.
5. Pop the white button out of the upper black surround. Sand the circumference of the white button evenly until it slips easily in and out of the black surround. A little silicon spray is a good idea.macnutz_27.jpg
6. Reassemble unit and check it has full movement (see photo below). macnutz_30.jpg
7.
On the underside of the button unit a ramp shape should lineup with an opening in the bottom edge.macnutz_33.jpg
8. Fit button unit back into upper seat leg, Fit lower seat leg aligning it to the back of the button unit so the push rod in the lower seat leg pushes on to the ramp on the button unit. Note the seat button will not come out and lock until the seat is fitted back on to the chassis pushing the rod up to push the button out to the lock position. Once you have fitted the back screw in you can use a large screw driver to push down the inside of the lower leg to check the white button pops out and locks. If you have any resistance dismantle again to check alignment and the condition of the interlocking teeth of the button and the outer rings. Sand of any burrs and use a little silicon grease. Reassemble and test again.
Repeat operation to the other side if necessary. Buttons are not interchangeable so doing one side at a time avoids mixing them up.
If the tabs on the white button are broken you can buy a new button unit as a part www.babycare.nl/bugaboo-cameleon-seat-frame-push-buttons-p-2664.html

on Jan 14, 2011 | Bugaboo Cameleon Jogger

1 Answer

Can't assemble the push handle in little tikes 3 in 1 purple


Hi Blanca,

We'd recommend you contact Little Tikes direct for assistance -

Mar 05, 2014 | Little Tikes 3 in 1 Trike Purple

2 Answers

Can't fold phil and teds dash,


I successfully fixed this issue today on a 2008 dash stroller. first remove the handle, you will need to drill out the two rivets with a 1/4" drill bit, but don't go too far, don't drill out the plastic on the handle piece. unscrew the four brake cable clips. unscrew the two screws securing the grey release clips. Prop stroller on the handle bar side (put padding underneath so you don't mess up your work surface) and the rear wheels. now get two small bladed screw drivers, you can gradually pry down the internal plastic locking wedge on either side till it releases the front wheel section which folds down. (on the left side which is likely functioning, you can just pull the plastic circular piece down with your fingers, as the internal wire is still connected)
Now grab some vise grips, lock onto the locking wedge and remove the whole mechanism, also remove the foam inside with a screw driver (this likely is what was supposed to keep the tension wire in place). Take the locking wedge mechanism apart. ( you will need to push the steel pin out with a small screw, it does not take a lot of force) Get a small nylon zip tie and secure it around the shaft on the tension wire connecting end of the locking wedge. (this will keep it from ever falling out(pulling through) again. This part (the locking wedges) should have been made out of aluminum or stainless steel and the issue would never occur. You will need to trim the catch end of the zip tie and make sure that it can slide freely inside of the plastic sleeve. now slide off the nylon zip tie and set it aside along with the spring.
Take the circular plastic piece (the 4" part inside that is near the handle piece with slots in it) slide in the tension cable. Slide the other end of the tension cable into the frame from the handle bar side till you can reach the end from the front wheel side. Now slide on the tubular plastic wedge housing and lock it in place to the frame (the detente underneath the frame lines up with the bump on the tubular sleeve), then the spring, then the small nylon zip tie, then the release wedge. Secure the zip tie onto the release wedge shaft and aim the head of the zip tie down so it can slide freely. Put some Vaseline or white lithium grease on the release wedge so it slides well. If the release wedge binds up you will need trim the zip tie head a bit more so it fits.
Next take the removed riveted posts and drill them out with a sharp 1/8" drill bit about 3/8" deep. (Use vise grips to hold onto these guys, as they will get hot, and make sure to use some oil while you drill to keep things cooler. Slide down the plastic circularly plastic pieces (you may need small screw driver to manipulate them down) so you can re-attach the two grey release mechanism brackets.
Re-insert the two formerly riveted brackets through the frame which will locate the handlebar properly. Get two small 1/4" sheet metal screws. Put the black washer back on, apply firm pressure and screw in the 1/4" sheet metal screws into the drilled out posts with a drill.
Re-attach the seat and you are good as new.
Note: The instructions may seem a little tricky, but you can do it.

f9f0b2d7-2a4b-4dfd-9821-02a9897f4ff3.jpgc1d48f09-768c-4abc-bc3c-e9f736076c24.jpg7edd1973-f3cc-42de-98b6-a455fdac45a6.jpg

Jun 25, 2012 | Phil & Teds Dash Stroller and Accessories...

1 Answer

I need assembly instructions for the Little Tikes Cozy truck


I have just downloaded the instructions for one of their cozy trucks at littletikes.co.uk
I would expect the instructions you are seeking would also be available.
Good luck.

Jun 27, 2011 | Little Tikes Cozy Cruiser Twin Seat Jogger...

1 Answer

Need to take zapp cover off!!!!!!!!


- place the quinny zapp in the halp open position
-unfasten the hooks
-slide the coverstops over the groove
-loosen the covers at the foot end and the cover should come off.

Nov 06, 2008 | Quinny ZAPP Stroller

2 Answers

How can I remove the tray?? Or can I?


Pleaes locate your product no. and the manufacture date.
You can find these:

On the frame
or
On the back of the seat

Apr 22, 2008 | Baby Strollers

5 Answers

Bertini M5 Shuttle


hi I think I could help I bought a bertini shuttle as well if you stand behind the pram on the right run your hand down the right side of the hood there is a push up lever there mine is grey ok you need to push the grey? lever but also on the left and right there is a black lever you must push up al together hope this helps good luck from debbie

Jan 09, 2008 | Bertini M5 - TS City Stroller

2 Answers

Reclining back problem


I'm having the same problem. It's very frustrating.

Dec 05, 2007 | Peg Perego Aria OH - Free Style Mint...

Not finding what you are looking for?
Baby Strollers Logo

Related Topics:

3,130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baby Strollers Experts

Stephen Faulkner
Stephen Faulkner

Level 2 Expert

541 Answers

Jennifer Rock
Jennifer Rock

Level 2 Expert

105 Answers

Iron
Iron

Level 3 Expert

3018 Answers

Are you a Baby Stroller Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...