Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I keep getting an F35 code on the front panel

Posted by on

  • 5 more comments 
  • Michael Masters
    Michael Masters Aug 24, 2010

    There are no f-35 codes for the duet series washer....

  • jdeere855 Aug 24, 2010

    Yes there are f 35 codes on the duet steam washer.. the service buletin in the lower compartment of the washer says that it is a analog pressure sensor failure or any malfunction of the steamer component.. even if we don't use the steam function, it makes the washer shut down

  • jdeere855 Aug 24, 2010

    i am wondering ifit is just a bad circuit board?

  • Michael Masters
    Michael Masters Aug 24, 2010

    I see. You didn't post a valid model number so i couldn't actually tell which unit you had. Ok, what is your model number?

    I need the entire model number so I can post the correct part number. it is not the CCU. That is ok. No issues there...

  • jdeere855 Aug 24, 2010

    it is the WFW9500TW01 model #

  • jdeere855 Aug 24, 2010

    serial # CSW1609372

  • jdeere855 Aug 24, 2010

    i just removed the part in under 5 minutes by taking the top off only. It is tucked right under the top of the washer on the right hand side if you are facing the front. No need to remove the rear panel at all, there is more than enough space to do what you need to do from the top

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

Thanks. Ok, the only part that is of importance will be the actual analog pressure sensor switch. You will only need to replace this part. This part fails in most duet sport(Steamers) models of this nature. It is mounted just next to the Electronic board that is located and mounted on the inside of the washer cabinet. The drum must be removed to access it and the top/front panel, as well. I will post the links to the diagram and part number for the part, below. The actual part that will need to be replace will be labeled number 20 on the diagram provided below.

Exploded Diagram

Analog pressure sensor switch part number -W10156252

Posted on Aug 24, 2010

Testimonial: "Thanks you have been very helpfull"

  • 2 more comments 
  • Michael Masters
    Michael Masters Aug 24, 2010

    Correction:

    You may be able to access the switch by just simply removing the rear access cover. This switch is very close to the rear access cover(Top Left Corner When Facing the rear of the unit). Try to reach it that way. It may not be necessary to disassemble the entire unit.

  • jdeere855 Aug 24, 2010

    Actually it is acessible from just removing the top of the washer. Thanks

  • Michael Masters
    Michael Masters Aug 24, 2010

    This should be possible, as well. I would remove the top and rear access panel to insure proper working space.

  • Michael Masters
    Michael Masters Aug 24, 2010

    Good deal; I'll update my notes to reflect that replacement procedure.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore elite front load washer model 46752701 after replacing pressure control switch i still get f35 code


Most common cause for the F35 error code: Using non-HE detergent. Detergent slime builds up in the hose, eventually getting into the analog pressure switch and killing it. Make sure you flush out as much soap as possible and make sure to use HE soap or it can keep occurring, also some vinger can calm down the suds

Oct 26, 2013 | Kenmore Elite HE3 Steam 8674 Dryer

1 Answer

Whirlpool front load washer keeps flashing F35 code


F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa!!

Jan 09, 2011 | Washing Machines

1 Answer

My Kenmore HE5T washer - Why do I keep getting code F35 and the machine won't completely wash the clothes.


F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.
If you remove the top panel, three screws in the back, you will have access to the pressure switch.
With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.
If the fault codes return after doing this, you will likely need to replace the pressure switch.

Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating and POSITIVE TESTIMONIAL is appreciated for answering your FREE question.

Oct 07, 2010 | Kenmore Elite 45986 Front Load Washer

1 Answer

I have an F35 Code that keeps comming up. I start the washer and then it says code SUDS after spining out then it goes into F35 Code. I'm using the HE Soap.


Hi, Both of these fault codes point to a pressure switch issue. If you remove the top panel, three screws in the back, you will have access to the pressure switch. With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions. If the fault codes return after diong this, you will likely need to replace the pressure switch

Sep 17, 2010 | Kenmore Elite 45986 Front Load Washer

1 Answer

Trouble code f35


The problem is likely the analog water level switch is failing. A pretty common problem in this machine. Before replace check the hose that goes to it for any blockage. If the hose is not plugged up the switch will need replaacing. Not a cheap part either but easy to replace. It is a small square block with wires and a hose going to it located under the top cover panel. For diagrams and illustrations enter your model # at www.appliancehelponline.com

Jul 13, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Error code F35


The F35 indicates that the main control board detects a problem with the analog pressure sensor (water level pressure switch) in the washer. This component senses and controls water level in the washer. This failure could be caused by a pinched or broken air hose between the air trap at the bottom of the washer tub and the analog pressure sensor. It can also be caused by a clogged air trap or a failed analog pressure sensor. If you are able to unplug the washer and pull off the top panel, you can check for the probable cause of this failure.

To remove the top panel, remove the screws on the very back of the panel that secure it to the washer cabinet. Pull the top panel back slightly and then and off of the washer. It is on the side wall just behind the expansion control board. You can check the air pressure hose connection and the wire harness connection on this component.

This component costs around $99.This information was based on the general description of the washer model that you provided (Kenmore Elite front load washer). There are several different models of this washer. I am not aware of other uses of the F35 code on the various models. If you intend to diagnose and repair this problem yourself, I recommend resubmitting your question with the full model number of your Kenmore washer so that we can verify this technical information using your model number.

Jun 08, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

I have a kenmore Elite...F35 keeps flashing..what does this mean. Please help


F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.*(&^%#

May 14, 2010 | Kenmore Elite 45986 Front Load Washer

3 Answers

Suds and F35 keep shuting down my laundry day:(


Remove the service panel and see if the filter has something in it77cb04b.jpg2402fad.jpgf032166.jpg

May 02, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My Kenmore Elite HE 5T Steam Front Loading Washer keeps flashing the code F35. What does this mean? It is not in the manual.


F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 02, 2010 | Kenmore Elite 45986 Front Load Washer

1 Answer

My Kenmore Elite he5t steam washer gets F35 error code


F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.@#$%

Feb 21, 2010 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2122 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...