Screen out of adjustment - RCA R52WH73 Projection Television

The ST651 display adjust settings will vary depending on the specific model of your display, but generally, the settings that can be adjusted include:

1. Brightness: Adjusts the overall brightness of the screen.
2. Contrast: Adjusts the difference between the lightest and darkest areas of the screen.
3. Color temperature: Adjusts the color temperature of the screen, which affects the overall color balance.
4. Gamma: Adjusts the mid-tones of the screen, which can affect the overall contrast and color balance.
5. Sharpness: Adjusts the sharpness of the edges of objects on the screen.
6. Overscan: Adjusts the size of the image on the screen, allowing you to zoom in or out to fit the entire image on the screen.
7. Aspect ratio: Adjusts the proportion of the width and height of the image on the screen.
8. Color format: Adjusts the format of the color on the screen, such as RGB, YCbCr, and so on.
9. Audio settings: Adjust the volume, bass, treble and audio output settings of the display.

You may find these settings in the on-screen menu of the display and you can use the remote control or buttons on the display to access and adjust the settings. Some settings may not be available for certain models, and it's worth consulting your display's user manual for specific instructions on how to access and adjust the settings on your particular model.

Hello,

follow the steps below;
At the right down part of your screen, right-click on your battery bar, scroll to "Adjust screen brightness"
Look down, at the middle of the screen, you will find screen brightness there.

I hope this helped.

Regards.

Initial Mode Function Setting Procedure
1. Remove the Compact Flash Cover [1].
2. Press the Warm Restart switch [2].
3. When "." appears at the center on the left-hand side of the screen, enter "3" from the
10-Key Pad.
4. Enter the 8-digit service code and touch [END]. (Default value: 00000000)

Touch Panel Adjustment

Functions • To adjust the position of the Touch Panel display
Use
• Make this adjustment if the Touch Panel is slow to respond to a pressing action.
• When the control panel is replaced.
Adjustment
Procedure
1. Touch [Touch Panel Adjustment] from the Initial mode screen.
2. Following the arrow mark, touch the four points (+) sequentially on the screen using a
pen.
NOTE
• Be sure to touch the very center of each point.
• Use care not to damage the screen surface with the tip of the pen.

Try to adjust the screen voltage a little up. It sounds that either screen voltage has been gone low, or the sub brightness setting have some
fault in circuit. See the screen control adjustment potmeter. It is Attached with line output transofrmer shown above. There will be to adjustment potmeaters, marked as 'screen' and 'focus'. Adjust the screen, the lower one, to a little bit, and try.

It looks like its the screen fit, adjustments. You know how you can adjust a computer screen?, well it's the same on a flat screen. Find the menu button and move the picture so it fits the screen. Also try adjusting the resolution. It could also be the convergence. Go to settings, menu and find how to adjust the convergence. Ten make sure the little box on the adjustment screen is in the middle of the tv screen. If its not move it there. Hope these tips help.

The best way to adjust the screen is to adjust the screen resolution until you get a correctly proportioned image.
First display an image such as a square or a circle on the screen.
Go to Control panel - Display - Settings tab and start with 1024 X 768 screen resolution adjustment
click Apply and the check your image.
Repeat the adjust screen resolution select the next highest screen resolution setting, repeat thia process until you get the best image.

Hello

If your TV has nice thread like horizontal lines on the entire screen, at aboug 1 inch apart or so, it is due to the high screen voltage. In some sets, this voltage may go high due to a defect in screen control adjust preset, integrated to line output transformer [LOT].
You just open your tv and locate the screen adjust control. It can be seen on the above said LOT itself. There will be two adjustable controls, one for adjusting focus voltage, and the other for adjusting the screen voltage.
Dont touch the focus adjuster. The screen adjuster will be at the bottom of the focus control, and both of them have visual markings there stating 'Focus' and 'Screen'.
Just turn the screen adjust control a little, while looking the picture on the screen, and adjust it till the lines on your screen just disappears. Never turn more than this position. The turning must be counterclokwise, not clokwise, as this should shut of your TV.
Take every precautions when we works with an elelctrical equipment. As high as 25,000VDC points are there, while tv is working, you should be very cautious. Do this with confidence. Take care. OK.

check the tail end of the picture tube do you see a light on it?that is the heater of the picture.without it your screen will be black. If there is no light from the heater there should be an open resistor connected to he heater replace them. .next check the screen adjustment of your plyback.screen adjustment is right in the body of the plyback there are 2 adjustment in there the upper is the focus adjustment and the lower is the screen adjustment turn it clockwise untill you reach the preferred adjustment.. tnx

please rate my help

XP =controll panel > display > adjust screen resolution

vista= controll panel > adjust screen resolution

I am not 100 percent what you are asking but I will answer the best I can with your question.

1. Press the [Administration] button located above the numeric keypad on the Control Panel. The Administration button has a wrench symbol located above it. The Access screen will be displayed.
2. Select [Tools] on the Touch Screen. The Tools Access Number screen will be displayed.
3. Enter your numeric password using the keypad.
   
   NOTE: If you do not know the password, contact your administrator. The initial password at machine install is 11111.
   
   If the administrator encounters a problem with changing or forgetting the machine password, a service call must be placed:
   
   
4. Select [Enter] on the Touch Screen. The Tools screen will be displayed.
5. Select [System Image Quality]. The System Image Quality screen will be displayed.
6. Select [Image Recognition]. The Image Recognition screen will be displayed.
7. Select 'Screening Adjustment' by selecting the [Up] or [Down] arrow buttons.
8. Select [Change Settings]. The Screening Adjustment screen will be displayed.
9. Select [Apply to Copies Only] then select [Save]. The Screening Adjustment screen will be displayed.
10. Select [Close]. The System Image Quality screen will be displayed.
11. Select [Auto Screening Adjust]. The Auto Screening Adjust screen will be displayed.
12. Select [Halftone Screen]. The Halftone Screen will be displayed.
13. Select either [Halftone 200 line screen] or [Photograph 200 dpi].
    
    NOTE: Do not select 'Printer use' as this will effect print calibration; which will be handled directly by the color server set up to print to the copier / printer.
    
    
14. Select [Save]. The Auto Screening Adjust screen will be displayed.
15. Insert at least 2 sheets of white, 216 mm x 279 mm (Letter, 8.5 x 11 inch) paper in Paper Tray 5 (Bypass Tray).
16. Select [Print Test Original] to print a sample of the settings. The message 'Please wait…Printing test original' will be displayed and the test original will print.
    
    NOTE: If selecting [Print Test Original] displays the message ‘System Disabled' then Screening Adjustment is disabled. Select [Close] and repeat steps 5 to 16.
    
    
17. Open the Document Glass Cover.
18. Place the test original face-down on the Document Glass with the two magenta squares against the left edge of the glass.
19. Place 5 sheets of blank white paper directly on top of the test original.
20. Close the Document Glass Cover.
21. Select [Start Adjustment] from the Touch Screen. The message 'Please wait….Adjustment in progress' will be displayed, then the Auto Screening Adjust screen will be displayed.
22. Select [Adjustment Complete]. The message 'Please wait…Printing current settings' will be displayed and the adjusted original will be printed.
23. Examine the adjusted original to make sure the image quality is satisfactory and continue to the next step. If the image quality is not satisfactory repeat steps 12 through 22.
24. Select [Close]. The System Image Quality screen will be displayed.
25. Select [Close]. The Tools screen will be displayed.
26. Select [Close]. The default copy screen will be displayed