Question about PC Desktops

1 Answer

Router not working, need to attach linksy router in order to obtain wireless internet

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 790 Answers

Reset it once ... using the reset pin available on rear side

Posted on May 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Linksys router password


To reset the Linksys back to the default settings - Press and hold the pinhole RESET button at the back of the router with the power ON for 20 secs. then release the RESET button.
To connect to your wireless router, the router's wireless settings needs to be configured with the SSID, encryption etc. and also the wireless cards in all the laptops/computers needs to be configured with these router's wireless settings. Then the laptops/desktop computers can communicate with your wireless router.
Connect a LAN cable from the Linksys to the LAN port on your computer.
Open a browser and enter the Linksys configuration URL
http://192.168.1.1
The default login = admin
The default PW = admin
You can protect your router by changing the default admin PW (write it down and put it in a safe place)
Go to the wireless configuration and set up the SSID and WPA or WPA2 encryption to protect your wireless network and Internet from unauthorized access.
Now apply these settings to the wireless card in your laptop/computer.
To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Jan 01, 2013 | PC Desktops

1 Answer

How do I connect my linksys wireless router?


Here are the steps :

1.Attach the antennas to the Linksys wireless router.

2.Place the router in a central location, making sure it's not surrounded by metal. (A signal can't be obtained through metal.) The router should be located so that the distance between clients (computers) is somewhat equal. This will create a better connection.

3.Plug the Ethernet cable into the "Internet" port on the back of the Linksys router.

4.Connect a computer to the router by plugging another Ethernet cable into the Ethernet port on your computer and attaching the other end to one of the available ports on the back of the router. You can choose any port except the one labeled "WAN."

5.Plug the router into an electrical outlet.

6.Wait for the power light to stop flashing, at which time the router is finished booting up. While the router is booting, the power light will be blinking. This process may take a few minutes to complete.

7.Reboot your computer so it can access a new IP address from the router through the Dynamic Host Configuration Protocol (DHCP).

Configure the Router procedure.

1.Open your web browser, type " http://192.168.1.1/ " into the address bar and hit "Enter."

2.Use "Admin" as the username in the pop-up box and leave the password blank.

3.Connect to the Internet and click on "Internet Setup."

4.Select your connection type from the drop-down menu. Choose "DHCP" for cable modems or "PPPoE" for most DSL modems. If you are unsure of these options, check with your ISP.

5.Set a service set identifier (SSID) to identify the router and change the password.

6.Encrypt your wireless connection using a Wireless Encryption Protocol (WEP) key. Under the "Wireless Security" option, enter a passphrase and click "Generate." This will generate a password which will need to be used by any client connecting to your router.

Sep 12, 2010 | PC Desktops

1 Answer

I cannot hookup my osx mac computer to the wireless at&t internet service i have set up in my home. The other 3 computers in our home do work (including another mac). We have called at&t tech...


What we really need is more information on the router. Do you know how the other computers connect to the wireless? Do you know if you had to have a password in order to connect? If you never did anything to the Linksys router to set it up, you can login to the router by opening Internet Explorer and browsing to 192.168.1.1. It will ask you for a login name and password. By default the name is blank and the password is "admin". If you look at the wireless settings you should be able to see the wireless settings, like the wireless name (again, by default the name is Linksys), what kind (if any) of encryption is used, etc.

May 27, 2009 | PC Desktops

1 Answer

I have Verizon Fios install in my home. I use to have Comcast. This is the situation, before the Fios my linksys wireless router was connected directly to a modem. Now my linksys wireless router is...


Your IP address for you linksys router needs to be changed.  More than likely there using the same IP address such as 192.168.0.1.
You have to convert your linksys router to a switch and change the IP address range it uses to on that doesn't conflict with the Verizon router.
10.150.1.1 should work.

Oct 08, 2008 | PC Desktops

1 Answer

Limited or no connectivity to the internet. my setup: the telephone port is approx 30m from where i need internet access. Originally I had a dlink wireless router set up but was connected via cable, now...


On which port of the D-link router did you plug the WRT160N router?

Do this setup.

Disconnect the WRT160N from D-link.

Connect a computer to port 1 of the WRT160N. Access the setup page by typing 192.168.1.1 on the address bar. you may need to type in the username and password for WRT160N. on the setup page Change the LAN IP address from 192.168.1.1 to 192.168.2.1. save the settings.

Connect a cable from port 1,2,3 or 4 of the D-link router to the Internet port of the WRT160N. turn off everything then turn them on starting from cable modem>D-link >WRT160N then computer.

You should be able to access the internet.

Oct 08, 2008 | PC Desktops

1 Answer

How do I set up my Linksys router?


Physical Setup of a LinkSys Router Each model of LinkSys router will differ slightly, but the general design is similar across all models. Therefore, the setup is similar across all models.
  1. Attach the antennas to the router (if your LinkSys router support wireless)d
  2. Plug the Ethernet cable from your broadband Internet provider into the port labeled "Internet"
  3. Plug another Ethernet cable into one of the available ports
  4. Plug the other end of that same cable into an Ethernet port on your PC
LinkSys Router Configuration LinkSys routers now ship with a Setup Wizard which is intended to simplfy basic configuration tasks.
We do not recommend the LinkSys Setup Wizard for two reasons:
  1. The Setup Wizard is not significantly easier that the regular configuration menus
  2. If you use the Setup Wizard, you will end up learning two interfaces for your LikSys router instead of just one
Instead, we recommend simply starting your web browser and jumping into the configuration.
Once your web browser is open, go to the URL http://192.168.1.1/. This will take you to a popup box which asks you to enter a username and password.
setup-linksys-router.jpg
Logging in to a LinkSys Router
The username is either blank or "admin" and the default password is "admin".
Once you are past the login screen, you are able to access (and change) a plethora of configuration options for your router.
Don't be worried by the enormous number and variety of options, your LinkSys router ships with default settings that enable it to work right out of the box in most environments.
From here the configuration options that you choose are largely up to your own personal preference.
If this is a wireless router, we recommend that you consider setting an SSID to identify the router as your own and configuring WEP to encrypt your wireless traffic.
LinkSys Router Setup Video Tutorials Learn how to set up your Linksys Router.





Thomas installs a Linksys router to demonstrate what ease-of-use means.

I really hope this information is helpfull.

Aug 12, 2008 | PC Desktops

1 Answer

I cannot set up my Linksys wireless router model number:WRT54GS to work properly. I have a desktop computer with Windows XP operating sysyem. I have three other laptop computers with wireless components


Hi,

The easiest would be to connect your desktop straight to your modem and verify that you can connect to the Internet. Do not use the LinkSys WRT54GS yet. Pop in the CD that came with the WiFi Router and run the setup wizard. Follow exactly on screen instructions. Verify that your desktop's networking is set to auto obtain IP address.

Alternately, you can try:
1. connect your desktop with a straight through LAN cable to Ethernet Port #1 of the WRT54GS;
2. set your desktop to use IP-192.168.1.10, Subnet Mask-255.255.255.0, Default Gateway-192.168.1.1;
3. open a browser and goto 192.168.1.1. use the LinkSys supplied username and password;
4. verify/configure/set the LinkSys to your preference;
5. for the time being do not use any security keyphrase, WEP WPA or MAC filter;
6. verify that your laptops could see the router's SSID;
7. verify that all laptops are set to auto obtain IP addresses;

If for some reason neither method will not work, pls post back with your modem's make & model.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

May 07, 2008 | PC Desktops

1 Answer

I have a DSL router provided by frontier. I am trying to make my desktop wireless. I believe that my DSL router functions as a modem also. I purchased a Linksys wireless broadband router. I can't not...


Your router should just be that, a router. Your connection is probably like fibernet the modem is actually on the outside of the house. This may help or may not but I have a linksys wired router that works very well but you have to go to their website in order to set up the router. You may need to look through your papers and find the web address to connect to the right site.

Apr 17, 2008 | PC Desktops

1 Answer

I have a linksy instant broadband etherfast cable/dsl router and I have WOW internet service. I'm been using a dell computer and just obtain a EMac computer and would like to share the WOW internet...


Greetings...

Which Linksys router do you have?
If it has 4 ethernet ports in the rear of the router you will need CAT 5 cable to run from the router to the computer...
One cable per computer...
The computer needs to have a network card in it...

So the setup is... WOW modem to Internet input on Linksys router and cables to each computer from the Linksys...

Ed

Apr 03, 2008 | PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...