We have a FES75-B and we are looking for a place to purchase replacement blade assembly. Can you help with this. My Email address is jerryhunt@connerindustriestx.com

If there is no noise without the beaker it will not be the motor. The problem is in the shaft & bush that holds the chopping blade. Dismantle, clean & lube it. If that does not fix it replacement of the assemble is the only other solution

Have a look on utube for your model and 'disassemble'.

I have one for sale.

Instruction to assemble a clipper blade.Above picture Socket
Spring Tension
Place Socket on Spring Tension like this
Slide Socket back as shown in picture
Turn Socket & Spring Tension over Make sure Socket is slide back
This is Call a Blade Guide Make sure the blade Guide is on the Spring Tension
Make sure blade guide is on like picture above, Now place Socket & Spring aside
The comb Blade Place comb blade as picture above
Place cutter blade as picture above, making sure cutter blade smaller blade is on the comb blade Rail.
Hold the blade like this Finger on top and Thumb on the bottom
Turn blade over like this while still holding the blade together
Place screw as shown
Screw in the screw don't tighten leave loose.
Now that you have the 2 screw in and not tight place the blade like this You need to hold the blade with one hand and with your Philips screw driver tap the cutter blade back lightly until the cutter teeth are 2/32 back from the comb blade.
the cutter blade which is the smaller blade is back 2/32 from the comb blade which is the bigger blade. When this is done by holding the blade together with your finger & Thumb
Tighten the 2 screws tight
Your blade should look like this when done correctly
We hope this was helpful when assembling a clipper blade.

If you live by any wal mart or hardware stores they should carry the components you are looking for. like sears they will have what you are looking for.

Yes you can, but they have made an assembly, meaning they want you to replace more than what is broken. The part number is 980640001 and you can purchase it at this site, or contact your local service center.

http://www.ereplacementparts.com/blade-clamp-assembly-p-156034.html

I had the same problem with the Wahl Pro Series Rechargeable model 8552, and called Wahl service. Here is what I learned:
Never unscrew the screws on a Wahl blade (they use those funky nonstandard screws to deter you) -- that's the main thing. The whole blade assembly is supposed to come off by pulling it up and off from the teeth.
But, if you did it (as I did), you can put it back together this way:
1. Place the large blade down on the table (Wahl logo down), and place the small blade on top of it (if you look carefully, you will see how it lines up).
2. Insert the spring points into the two holes of the white plastic part (on mine, the spring kept slipping out and I finally used a drop of superglue on each hole until it would stay in long enough to complete the assembly). Place that piece on top of the small blade (see photo).
3. The bent metal piece with the two screw holes then gets placed on top of the large blade, with the center ridge of the bent piece over the straight center portion of the spring -- so that you have to hold it in your hand and push it together against the spring in order to align the holes of the entire thing. As you are holding that, put the screws in from below and tighten. It's awkward and if you are like me, it will take several tries before you can get it all lined up correctly and tightened. The photo below is what the final assembly looks like before snapping it onto the clipper.
3. Clip it in: At the top of the assembly in the photo below, notice the small bent metal piece that will fit into the back of your clipper in the hole. Once you fit that properly, push the whole assembly down onto the clipper until it snaps into place.

I have not looked at the wipers on one yet but if they use a standard wiper, dont change the entire blade assembly. Change just the insert portion of the wiper blade if that is an option. Just lift the arm and then flatten back the blade assembly and a gap should form at one end so that you can slide the blade out from the the flex portion of the assembly. Then just stick the new inserts in the way you pulled the old ones out. At one time that was all that people used to replace. Now we think that we have to replace the flex portion as well but normally you dont. I dont have a 2005 Jaguar but it might also be a special blade you have to purchase. I have seen that before as well. Hope this helps...

I believe the blade is the same as my F-250, according to the manual. Pull the wiper away from the windshield, then push on either end of the blade, follow blade to pivot point at center, where blade pivots back and forth on wiper arm (wiper arm will not be moving as you do this). You need to push towards the windshield at this pivot point to push in on the wiper arm and out on the blade assembly to pop the round end of the wiper arm out of the hole in the blade assembly. Look at the new blade to see where this attaches. The new one should snap on to the arm when u squeeze the wiper arm to the blade. I prefer Exact Fit brand, as they seem to fit well. If u purchase at autozone, or advanced auto parts, they will install them for free.

It sounds as though one or both of the items are stripped. They mesh to drive the blade so I would not take a chance on just replacing just one. Also when you look at this you might also want to look at replacing the bearings and brushes. Make sure you clean out the gear housing or you will have immediate problems again. Also check where you buy these parts for their recommendation on the grease that needs to be used.