Question about Grindmaster Crathco granita machine, 2 hoppers

1 Answer

Drainage tubes in the Crathco granita machine broke out. Where can I get replacement parts. I am living in Nashville

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,236 Answers

If the black plasticbroke,you would need to replace the condensation tray. or, you could get a 3/8" double barb from a plumbing store and push it into the hole where it broke off and put the drain tube on the other end.

Posted on Aug 25, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Paddle does not turn what parts are needed

what does the display say? the shaft has an optic sensor. if the shaft pins or the sensor board are broken, it'll say sensor error. if the torque springs are broken, replace the shaft.

Apr 20, 2014 | Bunn Margarita Machine Ultra 2 Slush...

1 Answer

Oil coming out of back of machine

it isn't oil, it's old, syrupy slushie mix and dust. the only oil in the machine is inside the hermetically sealed (cannot open) compressor. you have a front seal problem. the shaft seal in the front inside the evaporator (steel tube), and the cup-shaped seal between the auger and the evaporator. slush is getting inside the shaft tube and dripping through the inside rear of the machine. replace the seals, lube with a food-safe lube and refill.

Mar 04, 2014 | Bunn Margarita Machine Ultra 2 Slush...

1 Answer

Where can I get a chi flatiron fixed in the Nashville, TN area? One of the ceramic plates broke lose.

I don't know about in Nashville, but you can send it in to Should be fixable.

Feb 06, 2011 | Chi Nano Digital Ceramic Flat Iron 1.25...

1 Answer

Leaking water on floor, even without water hooked up. Seems to be coming from under the fridge

Your freezer defrost drainage tube may not be routed to the evaporator tray under the refrigerator. If this is the case, humidity condensed from the freezer, then drained down the tube will be dripped onto the floor.
The second theory is that the drainage tube could be blocked. Humidity in the freezer is removed from the air sent to a drainage tray, at the rear of the freezer, which has a drainage tube which carries the water to an evaporation tray at the bottom of the refrigerator unit, on my GE. if the drainage tube is blocked, the water will find another route. Check the drainage tube after you find it. First try inspection. if there is standing water in tray in the freezer, use a flexible wire to clear the tube.
Good luck!

Oct 04, 2010 | GE Profile TPX24PBDCC Side by Side...

1 Answer

How do you clean filter on Bunn Ultra 2 granita machine

the filter is on the back of the machine. pull down on the ring and pull the filter out. spray it down with hot water and shake it dry. put it back in. on the front of the machine, there are 3 words below the display. these are buttons. press and hold the 2 outside ones until the filter message is cleared.

May 10, 2010 | Bunn Margarita Machine Ultra 2 Slush...

1 Answer

Auger shaft won't turn

the motor in the back has stripped a gear in the gearbox. you willneed to send it in tobe fixed, or replace the motor.

Aug 06, 2009 | Grindmaster Crathco granita machine, 2...

1 Answer

Have a g-23b cratcho granita machine, both sides start up after

if it freezes, the thickness of the mix triggers the torque switch to turn the compressor off. if it doesn't freeze all the way, the overload on the compressor triggers it to shut off to save the compressor from damage. it overloads if it gets too hot or the pressure is too high (also due to heat). make sure the condenser coils on the left side are clean and free of dust and obstructions, and make sure the fan is working to cool it down.

Apr 26, 2009 | Grindmaster Crathco granita machine, 2...

1 Answer

Model D690UX Delonghi deep fryer

Well I did solve my own dilemma. You have to unscrew the bottom black bolt in the bottom center of the unit. the open up the front panel to reveal a tiny screw just below the top center of the front panel. Remove it. Be very careful and remove the front panel. Pull lightly up on the inner black pot to reveal the clamp that holds the old drainage tube. Using a needle nose wrench, squeeze the clamp together to release the old tube and the clamp. Add new drainage tube inside the clamp and do the reverse. Make sure when you put the front panel back on, the open button's bottom part is inside a little **** or it will not work (it will fall out when you take front panel off). Make sure the little lamp is inside the red ON button.
Et Voila.....all fixed

Sep 21, 2008 | DeLonghi D690UX Cool Touch Deluxe Deep...

Not finding what you are looking for?
Grindmaster Crathco granita machine, 2 hoppers Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Grindmaster Coffee Makers & Espresso Machines Experts


Level 3 Expert

75108 Answers


Level 3 Expert

1198 Answers


Level 3 Expert

102366 Answers

Are you a Grindmaster Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides