Question about Radio Shack Cinego D-1000 Multimedia Projector

1 Answer

Blinking red power buttom

We just had the unit sent in for repair and when we went to hook it back up it will power up then the power button starts to blink red and then the unit shuts itself back off

Posted by on

  • Cousin Mark May 08, 2008

    Exact Same Problem.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 563 Answers

Hi frog31

I would suggest you take the unit back to the repairer immediately , they MUST fix the problem for you on their cost.

Posted on May 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Epson 460 powerlite hooked to smartboard green light blinking and no image.


Yes this is most likely the lamp. Does it eventually go back to just a red light?

Dec 06, 2012 | Epson PowerLite 410W LCD Projector

1 Answer

Replace the 2 bulbs. Unit powered up correctly and turned on like normal. Then Lamp1 and Lamp 2 indicator lights blinked (Indicating Start UP). After some period of time, it switched to Red 6 times blink...


1 red blink every 2.5 seconds indicates a cover error-- for this check the lamp cover
2 times red blinks very 2 seconds indicates temperature error. for this let the projector cool off check filters and fans that there is no blockage of air for proper cool down
3 red blinks every every 2 seconds Power error. incorrect voltage input or internal malfunction.
4 red blinks every 2 seconds indicates Fan Error check the fans make sure they are working and not blocked or need replacing.
i have nothing on 6 ligths go ahead reconect and check for proper count. hope this information helps.
Best of Luck.

Ray.

Jun 05, 2011 | Sanyo PDG-DXT10L Projector

1 Answer

My projector will not power on. I've replaced the cables, the power source, and the bulb but still nothing. The red standby led on the control unit turns blue when power button is pressed but goes right...


The ballast unit has most likely failed. Replace the ballast unit, unless the lamp exploded and in which case, there may be glass fragments stopping a fan from turning.

Feb 03, 2011 | Optoma HD81 DLP Projector

1 Answer

I actually have a 250. bulb is new but stopped working. When plugged in green power indicater lights then flashes two red lights.


The projector is bloked, you need reset the lamp timer. Press and hold the VOLUME + buttom, then press the VOLUME - buttom. Hold both buttons down for 10 seconds.

Jun 16, 2010 | InFocus LP 240 Multimedia Projector

1 Answer

Infocus X1 Projector started with 3 blinking red lights.


Its due to lamp Ballast power supply is faulty,it need to repair or replace otherwise again it will damage Lamp so be careful

Mar 09, 2010 | InFocus X1 Multimedia Projector

2 Answers

PROJECTOR PROBLEM Casio XJ 31


it wasn't able to go through cooldown mode. turn it on, power down and let it go through cooldown. does the light come on at all?

May 31, 2009 | Casio XJ-S31 Projector

2 Answers

Lamp will not come on


try pressing and holding the enter button on the projector for about 30 seconds - this resets it. It worked for me!!

Feb 10, 2008 | NEC VT460 Multimedia Projector

6 Answers

Unit will not Power Up.


Hi, we had the same problem... Bought a new lamp and then encountered the power light blinking repeatedly problem. After much frustration and anquish, we finally got it to work again... The way I did it was, take out the power cord from the back, then hold down the power switch and re-insert the cord. Somehow it made a difference to the unit and it powered back up all fine.. Cos we heard the fan come to life properly.
Cant guarantee it'll work for everyone but give it a try all the same.
Good luck

Nov 22, 2007 | InFocus ScreenPlay 5700 Multimedia...

2 Answers

NEC VT47 lamp won't light


According to the manual, yes . . .probably gone past the recommended hours of lamp use. Press the OFF or the HELP button on the remote for 10 sec, this will reset the lamp hours value and allow the unit to come on. If it don't, NEC will tell you that it has to be sent to a repair center.

Aug 29, 2007 | NEC VT470 Multimedia Projector

Not finding what you are looking for?
Multimedia Projectors Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Radio Shack Multimedia Projectors Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Sudeep Chatterjee
Sudeep Chatterjee

Level 3 Expert

3267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Radio Shack Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...